Difficulty

Moderate

Steps

10

Time Required

                          15 - 20 minutes

Sections

4

  • Top Propellor Blades
  • 3 steps
  • Bottom Propellor Blades
  • 1 step
  • Outer Shell
  • 3 steps
  • Drive Gears
  • 3 steps

Flags

0

  • BackPropel Gyro-X

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Top Propellor Blades
  • Stabilizing links are easy to break. Be gentle when prying them off.
  • Place the tweezers on the sides of the links and pull straight away from the top point of connection.

Stabilizing links are easy to break. Be gentle when prying them off.

Place the tweezers on the sides of the links and pull straight away from the top point of connection.

1024

Step 2

  • Remove the two 6.0 mm Phillips #00 screws from the rotors.

Remove the two 6.0 mm Phillips #00 screws from the rotors.

Step 3

  • Pull the rotors away from the mounting brackets.

Pull the rotors away from the mounting brackets.

Step 4

              Bottom Propellor Blades
  • Remove the two 5.0 mm Phillips #00 screws from the rotors.
  • The blades will fall off when the screws have been removed.

Remove the two 5.0 mm Phillips #00 screws from the rotors.

The blades will fall off when the screws have been removed.

Step 5

              Outer Shell
  • Locate the nubs on either side of the helicopter.

Locate the nubs on either side of the helicopter.

Step 6

  • Pull the body shell off of the nubs on both sides.

Pull the body shell off of the nubs on both sides.

Step 7

  • Push the front of the nose back towards the tail of the helicopter.
  • Push down on the shell and pull it away from the body, so that both slots pass over the hooks on the bottom of the helicopter.

Push the front of the nose back towards the tail of the helicopter.

Push down on the shell and pull it away from the body, so that both slots pass over the hooks on the bottom of the helicopter.

Step 8

              Drive Gears
  • Remove the two 8 mm Phillips #00 screws between the motor casing and the body.

Remove the two 8 mm Phillips #00 screws between the motor casing and the body.

Step 9

  • Remove the 4 mm Phillips #00 screw from the tail.

Remove the 4 mm Phillips #00 screw from the tail.

Step 10

  • Use your fingers to free the motor casing from the body, by bending the plastic body casing outwards at each of the four nubs.
  • Pull the motor casing upwards from the body.
  • The drive gear will slide out when you lift the motor casing.

Use your fingers to free the motor casing from the body, by bending the plastic body casing outwards at each of the four nubs.

Pull the motor casing upwards from the body.

The drive gear will slide out when you lift the motor casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors 


                    Jack Jenner

Member since: 04/08/2015

293 Reputation

                                      2 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 17-2, Forte Spring 2015                        

                                                  Member of Cal Poly, Team 17-2, Forte Spring 2015 



                    CPSU-FORTE-S15S17G2                     


                                            4 Members                     


                                            7 Guides authored