Difficulty
Difficult
Steps
10
Time Required
7 minutes
Sections
3
- Open Device
- 2 steps
- Motherboard
- 6 steps
- Screen
- 2 steps
Flags
0
BackProScan PLT7050
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Open Device
- Make sure device is unplugged and turned off while working on the device.
- Remove 2 Phillips head, 4.3 mm screws from the bottom side of the tablet with a PH00 screwdriver.
Make sure device is unplugged and turned off while working on the device.
Remove 2 Phillips head, 4.3 mm screws from the bottom side of the tablet with a PH00 screwdriver.
1024
Step 2
- Use the plastic opening tools to pry the back of the tablet open.
- You may need to slide the tool along the sides of the device to get it to open. You might hear some popping noises, it is okay.
- May be helpful if you start by the microSD slot.
Use the plastic opening tools to pry the back of the tablet open.
You may need to slide the tool along the sides of the device to get it to open. You might hear some popping noises, it is okay.
May be helpful if you start by the microSD slot.
Step 3
Motherboard
- Remove the 3 black pieces of tape from the device.
- Remove the 5 yellow pieces of tape from the device.
Remove the 3 black pieces of tape from the device.
Remove the 5 yellow pieces of tape from the device.
Step 4
- Use the soldering tool to remove the 3 wires from the mother board to the battery (black, red, gray).
- Soldering tool will get hot.
Use the soldering tool to remove the 3 wires from the mother board to the battery (black, red, gray).
Soldering tool will get hot.
Step 5
- Remove the speaker wires from the motherboard with the soldering tool.
Remove the speaker wires from the motherboard with the soldering tool.
Step 6
- Remove 3 Phillips head, 4.3 mm screws from the bottom side of the tablet with a PH00 screwdriver.
Remove 3 Phillips head, 4.3 mm screws from the bottom side of the tablet with a PH00 screwdriver.
Step 7
- Use the plastic opening tool to pop open all 3 ZIF connector tabs connected to the motherboard.
- Remove each ribbon from the ZIF connector port.
Use the plastic opening tool to pop open all 3 ZIF connector tabs connected to the motherboard.
Remove each ribbon from the ZIF connector port.
Step 8
- Lift the motherboard off the device taking care to pull the ports out of the casing.
Lift the motherboard off the device taking care to pull the ports out of the casing.
Step 9
Screen
- You will need two plastic opening tools.
- Use one of the plastic opening tools next to one of the black clips on the side of silver screen.
- Use the second plastic opening tool to push back the black clip next to the one you have worked on. Push the second plastic opening tool under the screen.
You will need two plastic opening tools.
Use one of the plastic opening tools next to one of the black clips on the side of silver screen.
Use the second plastic opening tool to push back the black clip next to the one you have worked on. Push the second plastic opening tool under the screen.
Step 10
- Wiggle the screen and pull it from the casing.
Wiggle the screen and pull it from the casing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Valerie Landguth
Member since: 01/19/2017
320 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Eastern Washington University, Team 1-4, Mathisen Winter 2017
Member of Eastern Washington University, Team 1-4, Mathisen Winter 2017
EWU-MATHISEN-W17S1G4
5 Members
12 Guides authored
