Difficulty
Moderate
Steps
16
Time Required
25 - 35 minutes
Sections
3
- Battery
- 3 steps
- Propeller
- 5 steps
- Top Shell
- 8 steps
Flags
0
BackProtocol Galileo
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Find door on the underside of drone. Open the door.
Find door on the underside of drone. Open the door.
1024
Step 2
- Carefully pull out battery, pulling out wires first.
Carefully pull out battery, pulling out wires first.
Step 3
- Disconnect the connecter.
- When reconnecting, remember to match up the black wire with the black wire and the red with red.
Disconnect the connecter.
When reconnecting, remember to match up the black wire with the black wire and the red with red.
Step 4
Propeller
- Use the heavy duty spudger tool to pry off metal caps by pushing the spudger up into the cap.
Use the heavy duty spudger tool to pry off metal caps by pushing the spudger up into the cap.
Step 5
- Twist the white spindle sleeve counter clockwise to align locking pin inside with the opening.
Twist the white spindle sleeve counter clockwise to align locking pin inside with the opening.
Step 6
- Use tweezers to remove locking pin.
Use tweezers to remove locking pin.
Step 7
- Pull off white spindle sleeve.
- Take note of which side of the spindle sleeve is the top.
Pull off white spindle sleeve.
Take note of which side of the spindle sleeve is the top.
Step 8
- Pull off propeller.
Pull off propeller.
Step 9
Top Shell
- Remove Blade Guards by unscrewing two 13 millimeter screws using Philips #0. Pull out the guards. Repeat the steps for the other three corners.
Remove Blade Guards by unscrewing two 13 millimeter screws using Philips #0. Pull out the guards. Repeat the steps for the other three corners.
Step 10
- Unscrew two 9 mm screws located inside the legs. Repeat the same procedure for the other three legs
Unscrew two 9 mm screws located inside the legs. Repeat the same procedure for the other three legs
Step 11
- Unplug the camera wire.
- Press the hold release button and slide out the camera module away from the button.
Unplug the camera wire.
Press the hold release button and slide out the camera module away from the button.
Step 12
- Remove the motor protection cover by unscrewing two 9 mm screws using Philips #0. When the screws are off, use your fingers to pull the motor protection cover off. Repeat the procedure for the other three arms.
Remove the motor protection cover by unscrewing two 9 mm screws using Philips #0. When the screws are off, use your fingers to pull the motor protection cover off. Repeat the procedure for the other three arms.
Step 13
- Unclip the motor cable from the shells housing using two pry tools. Repeat the same procedure for the other three arms.
Unclip the motor cable from the shells housing using two pry tools. Repeat the same procedure for the other three arms.
Step 14
- Remove 3 9mm screws around the motor housing. Repeat the steps for the three other arms.
Remove 3 9mm screws around the motor housing. Repeat the steps for the three other arms.
Step 15
- Remove four 9 mm screws located where the legs originally are placed. (Use a thin head screwdriver)
Remove four 9 mm screws located where the legs originally are placed. (Use a thin head screwdriver)
Step 16
- Cut the yellow strips using a scalpel. Pry open the casing using pry tools working gently around the corners.
Cut the yellow strips using a scalpel. Pry open the casing using pry tools working gently around the corners.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Thomas Ramey
Member since: 02/03/2017
301 Reputation
3 Guides authored
Badges:
4
+1 more badge
Team
UW Tacoma, Team 2-3, Rose Winter 2017
Member of UW Tacoma, Team 2-3, Rose Winter 2017
UWT-ROSE-W17S2G3
4 Members
5 Guides authored
