Protocol Slipstream Wifi Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 15 minutes

Sections

Camera
4 steps

Flags

BackProtocol Slipstream WiFi
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Camera

Remove the four 5.5 mm Phillips #00 screws that hold the lower canopy to the upper canopy.
Gently pull the lower canopy up and towards the back of the drone. The lower canopy will still be attached to the upper canopy by 3 wires. Just set the lower canopy aside and continue with the repair.
Be very careful when pulling the lower canopy apart from the upper canopy. There are 3 wires that will still be attached between the lower and upper canopies.

Remove the four 5.5 mm Phillips #00 screws that hold the lower canopy to the upper canopy.

Gently pull the lower canopy up and towards the back of the drone. The lower canopy will still be attached to the upper canopy by 3 wires. Just set the lower canopy aside and continue with the repair.

Be very careful when pulling the lower canopy apart from the upper canopy. There are 3 wires that will still be attached between the lower and upper canopies.

1024

Step 2

Remove the four 5.5 mm Phillips #00 screws that holds the battery tray to the lower canopy.
Once the four 5.5 mm Philips #00 screws are removed gently pull on the battery tray to separate it from the lower canopy.

Remove the four 5.5 mm Phillips #00 screws that holds the battery tray to the lower canopy.

Once the four 5.5 mm Philips #00 screws are removed gently pull on the battery tray to separate it from the lower canopy.

Step 3

Use a spudger to gently pry around the outside edge of the camera to remove the camera from its mounting hole.
Be careful when removing the camera from its mounting hole as there is a small ribbon wire that connects it to the computer.
The camera and computer assembly will now be free to move. Move the lower canopy out of the way for now.

Use a spudger to gently pry around the outside edge of the camera to remove the camera from its mounting hole.

Be careful when removing the camera from its mounting hole as there is a small ribbon wire that connects it to the computer.

The camera and computer assembly will now be free to move. Move the lower canopy out of the way for now.

Step 4

Use the flat side of the spudger and push the 2 tabs on either side of the camera connection on the computer and push the tabs towards the front of the drone (away from the computer).
Make sure both tabs are all the way out otherwise the ribbon wire for the camera will not be free and you can damage the wire by pulling on it.
Now remove the camera ribbon wire from the camera connection on the computer.

Use the flat side of the spudger and push the 2 tabs on either side of the camera connection on the computer and push the tabs towards the front of the drone (away from the computer).

Make sure both tabs are all the way out otherwise the ribbon wire for the camera will not be free and you can damage the wire by pulling on it.

Now remove the camera ribbon wire from the camera connection on the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    John Burkee

Member since: 09/17/2019

445 Reputation

                                      4 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Embry-Riddle Aeronautical University, Team S13-G5, Lamothe Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S13-G5, Lamothe Fall 2019 



                    ERAU-LAMOTHE-F19S13G5                     


                                            2 Members                     


                                            5 Guides authored

Introduction#

What you need#

#

#

#

#

#

#

Team#

#

Introduction

What you need

Team