Difficulty

Difficult

Steps

16

Time Required

                          35 minutes

Sections

4

  • Battery
  • 2 steps
  • Transmitter Board
  • 7 steps
  • Front Camera
  • 2 steps
  • Wi-Fi Antenna
  • 5 steps

Flags

0

  • BackProtocol Vento

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Grasp the tail end of the drone where the lip of the battery protrudes.

Grasp the tail end of the drone where the lip of the battery protrudes.

1024

Step 2

  • Pull away from the drone to remove the battery.
  • Do not attempt any repairs or replacements before removing the battery from the drone.

Pull away from the drone to remove the battery.

Do not attempt any repairs or replacements before removing the battery from the drone.

Step 3

              Transmitter Board
  • To get into the drone, twelve total screws need to be removed:
  • Ten 5.7mm Phillips #000 screws from the bottom of the drone body.
  • Two 4.5mm Phillips #000 screws at the front of the drone.
  • It is not necessary to remove the four screws on the arms of the drone.

To get into the drone, twelve total screws need to be removed:

Ten 5.7mm Phillips #000 screws from the bottom of the drone body.

Two 4.5mm Phillips #000 screws at the front of the drone.

It is not necessary to remove the four screws on the arms of the drone.

Step 4

  • Flip the drone over and lift off the top plastic shell of the drone.

Flip the drone over and lift off the top plastic shell of the drone.

Step 5

  • Remove the foam adhesive pad located on the Wi-Fi transmitter board.

Remove the foam adhesive pad located on the Wi-Fi transmitter board.

Step 6

  • Pry the gold Wi-Fi antenna connector, located under the previously removed foam pad, away from the Wi-Fi transmitter board to disconnect it.
  • Be sure to only apply force to the gold connector and not the black wire attached to it, as the connection between the two is very fragile.

Pry the gold Wi-Fi antenna connector, located under the previously removed foam pad, away from the Wi-Fi transmitter board to disconnect it.

Be sure to only apply force to the gold connector and not the black wire attached to it, as the connection between the two is very fragile.

Step 7

  • Remove the two 3.8mm Phillips #000 screws from the Wi-Fi transmitter board.
  • Be careful with the delicate ribbon cable attached to the camera.

Remove the two 3.8mm Phillips #000 screws from the Wi-Fi transmitter board.

Be careful with the delicate ribbon cable attached to the camera.

Step 8

  • Disconnect the white clip that connects the four colored wires (black, orange, red, blue) to the motherboard.
  • Be sure to pull only on the white clip, as to avoid damaging the wires.

Disconnect the white clip that connects the four colored wires (black, orange, red, blue) to the motherboard.

Be sure to pull only on the white clip, as to avoid damaging the wires.

Step 9

  • Gently pull the black wedge away from the main board until it shifts to a stop. You will feel it slide out, then stop.
  • The black insert acts as a wedge to keep the ribbon cable attached to the board. The wedge needs to be jostled loose before the cable can be removed.
  • Lightly pull the ribbon cable away from the connector.

Gently pull the black wedge away from the main board until it shifts to a stop. You will feel it slide out, then stop.

The black insert acts as a wedge to keep the ribbon cable attached to the board. The wedge needs to be jostled loose before the cable can be removed.

Lightly pull the ribbon cable away from the connector.

Step 10

              Front Camera
  • Remove the two 4.9mm Phillips #000 screws securing the camera to the front of the drone body.

Remove the two 4.9mm Phillips #000 screws securing the camera to the front of the drone body.

Step 11

  • Lift the camera holder and the camera up and away from the drone.

Lift the camera holder and the camera up and away from the drone.

Step 12

              Wi-Fi Antenna
  • Unscrew the four 4.9mm Phillips #000 corner screws that are securing the motherboard’s black base to the drone.
  • It is not necessary to unscrew the motherboard from the black base.

Unscrew the four 4.9mm Phillips #000 corner screws that are securing the motherboard’s black base to the drone.

It is not necessary to unscrew the motherboard from the black base.

Step 13

  • Grasp and pull each of the four drone arms in the direction of their propellers, one at a time, to remove them from the drone.

Grasp and pull each of the four drone arms in the direction of their propellers, one at a time, to remove them from the drone.

Step 14

  • Gently pull the motherboard out of the drone.
  • The four arms of the drone will dangle from the motherboard by their cords.

Gently pull the motherboard out of the drone.

The four arms of the drone will dangle from the motherboard by their cords.

Step 15

  • Pull the black, rectangular shell out of the drone.
  • It is not attached with screws.

Pull the black, rectangular shell out of the drone.

It is not attached with screws.

Step 16

  • Hold the drone’s shell with both hands so that the inside of the shell is facing you.
  • Gently flex the shell outward, so that the two latches (holding the antenna in place) move apart slightly.
  • At the same time, push the antenna from the back of the drone towards you until it releases from the latches.

Hold the drone’s shell with both hands so that the inside of the shell is facing you.

Gently flex the shell outward, so that the two latches (holding the antenna in place) move apart slightly.

At the same time, push the antenna from the back of the drone towards you until it releases from the latches.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    Maria Larcomb

Member since: 02/15/2018

926 Reputation

                                      5 Guides authored                  



                       Badges:
                       18







                                                        +15 more badges

Team

                       USF Tampa, Team S1-G2, Leahy Spring 2018                        

                                                  Member of USF Tampa, Team S1-G2, Leahy Spring 2018 



                    USFT-LEAHY-S18S1G2                     


                                            4 Members                     


                                            6 Guides authored