Featured
Featured Guide
Difficulty
Easy
Steps
10
Time Required
10 minutes
Sections
3
- Battery
- 1 step
- Casing
- 5 steps
- LCD Screen
- 4 steps
Flags
2
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackPSP 300x
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place the PSP face down and locate the battery cover on the left side of the device.
- Lift and remove the battery cover to reveal the battery.
- Remove the battery.
Place the PSP face down and locate the battery cover on the left side of the device.
Lift and remove the battery cover to reveal the battery.
Remove the battery.
1024
Step 2
Casing
- Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.
Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.
Step 3
- Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.
- Two are located behind the battery’s warranty sticker.
- Two are located on the right side of the PSP.
Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.
Two are located behind the battery’s warranty sticker.
Two are located on the right side of the PSP.
Step 4
- Next, unscrew the two screws located at the top of the PSP.
Next, unscrew the two screws located at the top of the PSP.
Step 5
- Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).
Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).
Step 6
- Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.
- Remove the front casing completely.
Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.
Remove the front casing completely.
Step 7
LCD Screen
- Push the homebar to the right to release the tab located on the right side of the LCD screen.
- DO NOT completely remove the homebar, as it is still connected by ribbon cables.
Push the homebar to the right to release the tab located on the right side of the LCD screen.
DO NOT completely remove the homebar, as it is still connected by ribbon cables.
Step 8
- Slowly lift the LCD screen off the PSP starting at the top edge corner.
- Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
- Orientation of PSP is flipped in photo.
Slowly lift the LCD screen off the PSP starting at the top edge corner.
Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
Orientation of PSP is flipped in photo.
Step 9
- Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.
- Pull all four ribbon cables out.
- Now remove the LCD screen and homebar from the PSP.
Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.
Pull all four ribbon cables out.
Now remove the LCD screen and homebar from the PSP.
Step 10
- Remove the metal tab that lies above the LCD screen.
- Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.
Remove the metal tab that lies above the LCD screen.
Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
46 other people completed this guide.
Author
with 15 other contributors
mbnewsom
Member since: 10/28/2009
2,932 Reputation
11 Guides authored
Badges:
15
+12 more badges