Difficulty

Easy

Steps

36

Time Required

                          15 - 20 minutes

Sections

9

  • Battery
  • 1 step
  • Casing
  • 5 steps
  • LCD Screen
  • 4 steps
  • Trigger Buttons
  • 6 steps
  • Analog Stick
  • 6 steps
  • Button Pad
  • 1 step
  • Power Jack
  • 4 steps
  • Speaker
  • 1 step
  • Motherboard
  • 8 steps

Flags

2

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackPSP 300x

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Place the PSP face down and locate the battery cover on the left side of the device.
  • Lift and remove the battery cover to reveal the battery.
  • Remove the battery.

Place the PSP face down and locate the battery cover on the left side of the device.

Lift and remove the battery cover to reveal the battery.

Remove the battery.

1024

Step 2

              Casing
  • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Step 3

  • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.
  • Two are located behind the battery’s warranty sticker.
  • Two are located on the right side of the PSP.

Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

Two are located behind the battery’s warranty sticker.

Two are located on the right side of the PSP.

Step 4

  • Next, unscrew the two screws located at the top of the PSP.

Next, unscrew the two screws located at the top of the PSP.

Step 5

  • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Step 6

  • Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.
  • Remove the front casing completely.

Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.


Remove the front casing completely.

Step 7

              LCD Screen
  • Push the homebar to the right to release the tab located on the right side of the LCD screen.
  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Push the homebar to the right to release the tab located on the right side of the LCD screen.

DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Step 8

  • Slowly lift the LCD screen off the PSP starting at the top edge corner.
  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
  • Orientation of PSP is flipped in photo.

Slowly lift the LCD screen off the PSP starting at the top edge corner.

Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

Orientation of PSP is flipped in photo.

Step 9

  • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.
  • Pull all four ribbon cables out.
  • Now remove the LCD screen and homebar from the PSP.

Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

Pull all four ribbon cables out.

Now remove the LCD screen and homebar from the PSP.

Step 10

  • Remove the metal tab that lies above the LCD screen.
  • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Remove the metal tab that lies above the LCD screen.

Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Step 11

              Trigger Buttons
  • Remove the screw securing ‘L’ trigger to the PSP.

Remove the screw securing ‘L’ trigger to the PSP.

Step 12

  • Remove the white plastic piece that holds the ‘L’ trigger in place.

Remove the white plastic piece that holds the ‘L’ trigger in place.

Step 13

  • Remove the ‘L’ trigger from the PSP.

Remove the ‘L’ trigger from the PSP.

Step 14

  • Remove the screw securing the ‘R’ trigger.

Remove the screw securing the ‘R’ trigger.

Step 15

  • Remove the white plastic piece that holds the ‘R’ trigger in place.

Remove the white plastic piece that holds the ‘R’ trigger in place.

Step 16

  • Remove the ‘R’ trigger from the PSP.

Remove the ‘R’ trigger from the PSP.

Step 17

              Analog Stick
  • Remove the screw from the bottom left edge of the PSP.

Remove the screw from the bottom left edge of the PSP.

Step 18

  • Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the ‘L’ trigger off the PSP.

Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the ‘L’ trigger off the PSP.

Step 19

  • Using a fingernail or spudger, flip up the retaining bracket on the d-pad and ‘L’ trigger ribbon cable.
  • Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.

Using a fingernail or spudger, flip up the retaining bracket on the d-pad and ‘L’ trigger ribbon cable.

Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.

Step 20

  • Remove the cable from the connector and remove the entire black piece from the PSP.

Remove the cable from the connector and remove the entire black piece from the PSP.

Step 21

  • Remove the screw holding the analog stick in place.

Remove the screw holding the analog stick in place.

Step 22

  • Flip up the lock on the analog sticks ribbon cable.
  • Remove the analog stick from the PSP.

Flip up the lock on the analog sticks ribbon cable.

Remove the analog stick from the PSP.

Step 23

              Button Pad
  • After removing the LCD Screen, the Button Pad should be easy to remove.

After removing the LCD Screen, the Button Pad should be easy to remove.

Step 24

              Power Jack
  • Flip up the lock and detach the ribbon cable above the power jack.

Flip up the lock and detach the ribbon cable above the power jack.

Step 25

  • Remove the screw from the power jack.

Remove the screw from the power jack.

Step 26

  • Carefully bend back the black tab holding the power jack in place and start pulling the jack up to release it from this clip.

Carefully bend back the black tab holding the power jack in place and start pulling the jack up to release it from this clip.

Step 27

  • Pull the plug connecting the power jack to the motherboard.
  • Remove the power jack.

Pull the plug connecting the power jack to the motherboard.

Remove the power jack.

Step 28

              Speaker
  • Push the black tab at the bottom of the speaker to pop the speaker out of place, and remove the speaker.
  • The speaker is spring loaded, so be sure to keep an eye on it in case it starts doing flips into the air when you push the tab. Be careful not to lose or damage it!
  • Make sure the new/replacement speaker does not spring out during reassembly.

Push the black tab at the bottom of the speaker to pop the speaker out of place, and remove the speaker.

The speaker is spring loaded, so be sure to keep an eye on it in case it starts doing flips into the air when you push the tab. Be careful not to lose or damage it!

Make sure the new/replacement speaker does not spring out during reassembly.

Step 29

              Motherboard
  • Remove the cable carefully by lifting upwards from port attached to the motherboard .

Remove the cable carefully by lifting upwards from port attached to the motherboard .

Step 30

  • Flip up both of the locks and remove both cables as shown

Flip up both of the locks and remove both cables as shown

Step 31

  • Flip up the lock and remove the ribbon cable located at the bottom edge of the PSP.

Flip up the lock and remove the ribbon cable located at the bottom edge of the PSP.

Step 32

  • Use a Phillips #00 screwdriver to remove the bottom left screw attached to the PSP

Use a Phillips #00 screwdriver to remove the bottom left screw attached to the PSP

Step 33

              Remove Power Switch Panel
  • Remove the screw located at the top of the power switch panel.
  • Gently lift and remove the panel from the switch side

Remove the screw located at the top of the power switch panel.

Gently lift and remove the panel from the switch side

Step 34

  • Remove the silver rim on the right side of the PSP.

Remove the silver rim on the right side of the PSP.

Step 35

  • Remove the silver rim on the left side of the PSP.

Remove the silver rim on the left side of the PSP.

Step 36

  • Remove the motherboard from the PSP

Remove the motherboard from the PSP

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      14 other people completed this guide.

Author

                                      with 15 other contributors 


                    mbnewsom

Member since: 10/28/2009

2,932 Reputation

                                      11 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges