Difficulty

Easy

Steps

13

Time Required

                          15 minutes

Sections

4

  • Battery
  • 1 step
  • Casing
  • 5 steps
  • LCD Screen
  • 4 steps
  • Power Board
  • 3 steps

Flags

2

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackPSP 300x

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Place the PSP face down and locate the battery cover on the left side of the device.
  • Lift and remove the battery cover to reveal the battery.
  • Remove the battery.

Place the PSP face down and locate the battery cover on the left side of the device.

Lift and remove the battery cover to reveal the battery.

Remove the battery.

1024

Step 2

              Casing
  • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Step 3

  • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.
  • Two are located behind the battery’s warranty sticker.
  • Two are located on the right side of the PSP.

Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

Two are located behind the battery’s warranty sticker.

Two are located on the right side of the PSP.

Step 4

  • Next, unscrew the two screws located at the top of the PSP.

Next, unscrew the two screws located at the top of the PSP.

Step 5

  • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Step 6

  • Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.
  • Remove the front casing completely.

Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.


Remove the front casing completely.

Step 7

              LCD Screen
  • Push the homebar to the right to release the tab located on the right side of the LCD screen.
  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Push the homebar to the right to release the tab located on the right side of the LCD screen.

DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Step 8

  • Slowly lift the LCD screen off the PSP starting at the top edge corner.
  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
  • Orientation of PSP is flipped in photo.

Slowly lift the LCD screen off the PSP starting at the top edge corner.

Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

Orientation of PSP is flipped in photo.

Step 9

  • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.
  • Pull all four ribbon cables out.
  • Now remove the LCD screen and homebar from the PSP.

Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

Pull all four ribbon cables out.

Now remove the LCD screen and homebar from the PSP.

Step 10

  • Remove the metal tab that lies above the LCD screen.
  • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Remove the metal tab that lies above the LCD screen.

Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Step 11

              Power Board
  • Using a spudger, lift up the lock and remove the ribbon cable from the motherboard

Using a spudger, lift up the lock and remove the ribbon cable from the motherboard

Step 12

  • Use a Phillips #00 screwdriver to remove the screw located on the power switch board.

Use a Phillips #00 screwdriver to remove the screw located on the power switch board.

Step 13

  • Lift up and remove the power-switch board.

Lift up and remove the power-switch board.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 10 other contributors 


                    mbnewsom

Member since: 10/28/2009

2,932 Reputation

                                      11 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

javi - Dec 21, 2022

Reply

for power board you can skip 7-10 steps ,1 to 6 is remove front case , real work start at step 11 ,between those was taking apart sreen, but not need for power board replacement.