Difficulty

Easy

Steps

14

Time Required

                          25 minutes

Sections

4

  • Battery
  • 1 step
  • Casing
  • 5 steps
  • LCD Screen
  • 4 steps
  • Power Jack
  • 4 steps

Flags

1

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

  • BackPSP 300x

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Place the PSP face down and locate the battery cover on the left side of the device.
  • Lift and remove the battery cover to reveal the battery.
  • Remove the battery.

Place the PSP face down and locate the battery cover on the left side of the device.

Lift and remove the battery cover to reveal the battery.

Remove the battery.

1024

Step 2

              Casing
  • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Step 3

  • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.
  • Two are located behind the battery’s warranty sticker.
  • Two are located on the right side of the PSP.

Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

Two are located behind the battery’s warranty sticker.

Two are located on the right side of the PSP.

Step 4

  • Next, unscrew the two screws located at the top of the PSP.

Next, unscrew the two screws located at the top of the PSP.

Step 5

  • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Step 6

  • Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.
  • Remove the front casing completely.

Slide the spudger in between the outer casing of the PSP, beginning at the “R” shoulder button, and gently pry off the casing.


Remove the front casing completely.

Step 7

              LCD Screen
  • Push the homebar to the right to release the tab located on the right side of the LCD screen.
  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Push the homebar to the right to release the tab located on the right side of the LCD screen.

DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Step 8

  • Slowly lift the LCD screen off the PSP starting at the top edge corner.
  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
  • Orientation of PSP is flipped in photo.

Slowly lift the LCD screen off the PSP starting at the top edge corner.

Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

Orientation of PSP is flipped in photo.

Step 9

  • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.
  • Pull all four ribbon cables out.
  • Now remove the LCD screen and homebar from the PSP.

Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

Pull all four ribbon cables out.

Now remove the LCD screen and homebar from the PSP.

Step 10

  • Remove the metal tab that lies above the LCD screen.
  • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Remove the metal tab that lies above the LCD screen.

Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Step 11

              Power Jack
  • Flip up the lock and detach the ribbon cable above the power jack.

Flip up the lock and detach the ribbon cable above the power jack.

Step 12

  • Remove the screw from the power jack.

Remove the screw from the power jack.

Step 13

  • Carefully bend back the black tab holding the power jack in place and start pulling the jack up to release it from this clip.

Carefully bend back the black tab holding the power jack in place and start pulling the jack up to release it from this clip.

Step 14

  • Pull the plug connecting the power jack to the motherboard.
  • Remove the power jack.

Pull the plug connecting the power jack to the motherboard.

Remove the power jack.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 14 other contributors 


                    mbnewsom

Member since: 10/28/2009

2,932 Reputation

                                      11 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

aONe - Mar 22, 2013

Reply

Really easy to follow, thanks. You can dismiss the 10 and 11 steps being careful.