Difficulty

Moderate

Steps

8

Time Required

                          1 minute

Sections

4

  • Battery
  • 1 step
  • Rear Backing
  • 1 step
  • Motherboard
  • 3 steps
  • Keypad
  • 3 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackQualcomm QCP-2760

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Unscrew the back battery plate from the phone using a T6 Torx screwdriver.
  • The screw does not need to be removed completely, the back battery plate will unhinge from the phone.

Unscrew the back battery plate from the phone using a T6 Torx screwdriver.

The screw does not need to be removed completely, the back battery plate will unhinge from the phone.

1024

Step 2

              Rear Backing
  • Using the T6 Torx screwdriver, remove the two screws located at the bottom of the back of the phone.
  • Find the seam between the front and back of the phone
  • Pry the seam open using a plastic opening tool, or your fingers.
  • Some force is required

Using the T6 Torx screwdriver, remove the two screws located at the bottom of the back of the phone.

Find the seam between the front and back of the phone

Pry the seam open using a plastic opening tool, or your fingers.

Some force is required

Step 3

              Motherboard
  • Locate the four metal clips holding the motherboard onto the phone.
  • Pull the clips away from the motherboard while lifting the motherboard out of the case.
  • The motherboard is attached to the case by a fragile cable, do not apply any stress to the cable.

Locate the four metal clips holding the motherboard onto the phone.

Pull the clips away from the motherboard while lifting the motherboard out of the case.

The motherboard is attached to the case by a fragile cable, do not apply any stress to the cable.

Step 4

  • Place the motherboard down so that the screen is facing up.
  • Grab the small brown connector plug at the sides with a fingernail or tweezers and flip it up.
  • Locate, but do not disconnect, the four screen clips.

Place the motherboard down so that the screen is facing up.

Grab the small brown connector plug at the sides with a fingernail or tweezers and flip it up.

Locate, but do not disconnect, the four screen clips.

Step 5

  • Flip the motherboard over so that the screen is facing down.
  • Again, be careful not to put stress on the speaker cable.

Flip the motherboard over so that the screen is facing down.

Again, be careful not to put stress on the speaker cable.

Step 6

              Keypad
  • Remove keypad circuit board by lifting up circuit board while pulling clip.

Remove keypad circuit board by lifting up circuit board while pulling clip.

Step 7

  • Remove rubber keypad

Remove rubber keypad

Step 8

  • Insert new rubber keypad.

Insert new rubber keypad.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Colin Packard

Member since: 09/30/2014

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Ohio State, Team 1-4, Buehl Fall 2014                        

                                                  Member of Ohio State, Team 1-4, Buehl Fall 2014 



                    OSU-BUEHL-F14S1G4                     


                                            4 Members                     


                                            10 Guides authored