Difficulty
Very difficult
Steps
13
Time Required
15 minutes
Sections
5
- Strap
- 2 steps
- Back Panel
- 2 steps
- Analog Battery
- 3 steps
- Circuit Board
- 2 steps
- Digital Battery
- 4 steps
Flags
1
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackQuiksilver The Fifty50
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Strap
- Place the watch (face down) on a solid surface.
- Carefully use the screwdriver and push in one side of the strap.
- Slowly remove the strap by pushing back one of the hidden metallic holders for the strap.
- If you are having difficulty trying to take off the strap, feel free to use a 3.5 flat head screw driver, or any kind of tool that make this step easier.
Place the watch (face down) on a solid surface.
Carefully use the screwdriver and push in one side of the strap.
Slowly remove the strap by pushing back one of the hidden metallic holders for the strap.
If you are having difficulty trying to take off the strap, feel free to use a 3.5 flat head screw driver, or any kind of tool that make this step easier.
1024
Step 2
- Gently pull the pin out of the strap.
- Carefully handle the small metallic holder, as they are sharp and may be difficult to locate if lost.
Gently pull the pin out of the strap.
Carefully handle the small metallic holder, as they are sharp and may be difficult to locate if lost.
Step 3
Back Panel
- Remove the four 1.1 mm screws holding the back panel in place using the Phillips #00 screwdriver.
Remove the four 1.1 mm screws holding the back panel in place using the Phillips #00 screwdriver.
Step 4
- Carefully separate the panel off of the watch.
- Careful not to lose the four 1.1 mm screw or else the back panel will not be able to put back.
Carefully separate the panel off of the watch.
Careful not to lose the four 1.1 mm screw or else the back panel will not be able to put back.
Step 5
Analog Battery
- Carefully lift the white plastic circular out of the watch.
Carefully lift the white plastic circular out of the watch.
Step 6
- Remove the four 1.1 mm screws located on the metallic holder using the Phillips #00 screwdriver.
Remove the four 1.1 mm screws located on the metallic holder using the Phillips #00 screwdriver.
Step 7
- Remove the large circular Analog battery.
Remove the large circular Analog battery.
Step 8
Circuit Board
- Using the Phillips #00 screwdriver, remove the two 1 mm screws holding the circuit board to the device.
Using the Phillips #00 screwdriver, remove the two 1 mm screws holding the circuit board to the device.
Step 9
- Remove the green circular chip using a pair of tweezers.
Remove the green circular chip using a pair of tweezers.
Step 10
Digital Battery
- Using the Phillips #00 screwdriver, remove the 1.1 mm screw that is holding the digital battery holder in place.
Using the Phillips #00 screwdriver, remove the 1.1 mm screw that is holding the digital battery holder in place.
Step 11
- Use the magnetic pick-up tool to remove the small screw.
- Careful to not lose this screw because it is crucial for putting the watch back.
Use the magnetic pick-up tool to remove the small screw.
Careful to not lose this screw because it is crucial for putting the watch back.
Step 12
- Lift up the battery holder.
Lift up the battery holder.
Step 13
- Remove the digital battery from the socket.
Remove the digital battery from the socket.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Sue Giske
Member since: 07/16/2019
622 Reputation
5 Guides authored
Badges:
10
+7 more badges
Team
UW Tacoma, Team S1-G4, Liner Summer 2019
Member of UW Tacoma, Team S1-G4, Liner Summer 2019
UWT-LINER-SU19S1G4
5 Members
5 Guides authored
