Difficulty

Moderate

Steps

4

Time Required

                          10 - 15 minutes

Sections

  • Rubber Feet
  • 1 step
  • Front Panel
  • 1 step
  • Back Panel
  • 1 step
  • USB Port
  • 1 step

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackRazer Blackwidow Tournament Edition Chroma

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Rubber Feet
  • Turn the keyboard over so that it is lying flat on its face.
  • Use the iFixit opening tool to pry the rubber feet off the keyboard.

Turn the keyboard over so that it is lying flat on its face.

Use the iFixit opening tool to pry the rubber feet off the keyboard.

1024

Step 2

              Front Panel
  • Use a Phillips #1 screwdriver to remove the six screws on the back of the keyboard.
  • Use an opening tool as a wedge between the front and back panel to pry open the front panel.
  • If the front and back panel won’t separate, DO NOT use excessive force. This may result in damaging the keyboard.
  • Instead, slide the opening tool across the keyboard in between the front and back panel. Go around the edges of the keyboard until the panels disconnect.
  • Flip the keyboard over so the keys are facing up.
  • Grabbing the left and right lips of the front panel, lift both ends up, removing the front panel.

Use a Phillips #1 screwdriver to remove the six screws on the back of the keyboard.

Use an opening tool as a wedge between the front and back panel to pry open the front panel.

If the front and back panel won’t separate, DO NOT use excessive force. This may result in damaging the keyboard.

Instead, slide the opening tool across the keyboard in between the front and back panel. Go around the edges of the keyboard until the panels disconnect.

Flip the keyboard over so the keys are facing up.

Grabbing the left and right lips of the front panel, lift both ends up, removing the front panel.

Step 3

              Back Panel
  • Use a Philips #1 Screwdriver to remove the four screws located below the keys.
  • Lift the main circuit board and flip it over, placing it on its top.
  • Be cautious of the wire connected to the USB Port Board.

Use a Philips #1 Screwdriver to remove the four screws located below the keys.

Lift the main circuit board and flip it over, placing it on its top.

Be cautious of the wire connected to the USB Port Board.

Step 4

              USB Port
  • Pull on the wire connector until it disconnects from the USB port board.
  • You may use either your hands or a pair of tweezers to separate the white connection clip.

Pull on the wire connector until it disconnects from the USB port board.

You may use either your hands or a pair of tweezers to separate the white connection clip.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Jonathan Stewart

Member since: 02/08/2018

294 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       University of North Texas, Team S6-G5, Thomas Spring 2018                        

                                                  Member of University of North Texas, Team S6-G5, Thomas Spring 2018 



                    UNT-THOMAS-S18S6G5                     


                                            4 Members                     


                                            10 Guides authored

Eduwardo Horibe - Dec 27, 2021

Reply

Where can I get another USB board? And it’s possible to build one from scratch? I was thinking in upgrading to a USB C port