Difficulty
Difficult
Steps
16
Time Required
30 minutes - 1 hour
Sections
3
- Razer Naga Trinity Disassembly
- 7 steps
- Scroll Wheel Housing
- 5 steps
- OMRON D2FC-F-K(50M) Micro Switch
- 4 steps
Flags
0
BackRazer Naga Trinity
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Razer Naga Trinity Disassembly
- Remove the interchangeable side plate.
Remove the interchangeable side plate.
1024
Step 2
- Remove the mouse’s feet using the opening pick.
Remove the mouse’s feet using the opening pick.
Step 3
- Remove the four 6mm screws by using a JIS #1 screwdriver.
Remove the four 6mm screws by using a JIS #1 screwdriver.
Step 4
- Separate the top mouse housing from the bottom mouse housing using the opening pick.
- Be careful not to tug too hard on the ribbon connector.
Separate the top mouse housing from the bottom mouse housing using the opening pick.
Be careful not to tug too hard on the ribbon connector.
Step 5
- Unlock the ribbon connector that is held down by the main board clips using the spudger’s pointed end.
Unlock the ribbon connector that is held down by the main board clips using the spudger’s pointed end.
Step 6
- Remove the side housing using the opening pick.
Remove the side housing using the opening pick.
Step 7
- Remove the top housing LED 3-Pin connector that is near the main board.
Remove the top housing LED 3-Pin connector that is near the main board.
Step 8
Scroll Wheel Housing
- Remove one 4mm black Phillips #000 screw from the left side of the mouse holding the scroll wheel LED controller board.
- Then pull the LED controller board upwards and out.
Remove one 4mm black Phillips #000 screw from the left side of the mouse holding the scroll wheel LED controller board.
Then pull the LED controller board upwards and out.
Step 9
- Pry and remove the scroll wheel feedback bar from its hold-down clips using the hook end of a halberd spudger.
Pry and remove the scroll wheel feedback bar from its hold-down clips using the hook end of a halberd spudger.
Step 10
- Remove the scroll wheel feedback bar from the scroll wheel by holding down the spring and using angled tweezers to remove it from its placement.
Remove the scroll wheel feedback bar from the scroll wheel by holding down the spring and using angled tweezers to remove it from its placement.
Step 11
- Remove the scroll wheel optical encoder 3-pin connector from the main board by wiggling the connector upwards.
Remove the scroll wheel optical encoder 3-pin connector from the main board by wiggling the connector upwards.
Step 12
- Using the opening tool, pry the black bracket holding the scroll wheel in place backwards until the scroll wheel housing pops out.
Using the opening tool, pry the black bracket holding the scroll wheel in place backwards until the scroll wheel housing pops out.
Step 13
OMRON D2FC-F-K(50M) Micro Switch
- Remove the USB Type A to 5-pin connector from the main board by pinching and pulling upwards.
Remove the USB Type A to 5-pin connector from the main board by pinching and pulling upwards.
Step 14
- Remove four 3mm JIS #1 screws holding the main board.
Remove four 3mm JIS #1 screws holding the main board.
Step 15
- Place the tip of the soldering iron onto the micro switch contact pins.
- Work around the micro switch pins while prying the switch with an opening pick.
Place the tip of the soldering iron onto the micro switch contact pins.
Work around the micro switch pins while prying the switch with an opening pick.
Step 16
- Remove and replace OMRON D2FC-F-K(50M) micro switch.
- Solder all three micro switch pins with soldering iron.
- Ensure the micro switch is bonded by performing a tug test.
Remove and replace OMRON D2FC-F-K(50M) micro switch.
Solder all three micro switch pins with soldering iron.
Ensure the micro switch is bonded by performing a tug test.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 4 other contributors
Zackary Tempert
Member since: 09/16/2019
217 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Embry-Riddle Aeronautical University, Team S6-G2, Salas Fall 2019
Member of Embry-Riddle Aeronautical University, Team S6-G2, Salas Fall 2019
ERAU-SALAS-F19S6G2
4 Members
6 Guides authored
incognito666z - Feb 1, 2021
Reply
dont bother. It took me 2 hours to get it replace and left click still dident work even when i heared it click. Just work some over time at work and buy a new
Andreas - Jul 11, 2021
If the switch is still clicking and you tried replacing it, the issue surely is somewhere else.
You should look if there are other parts inside that look “
Andreas - Jul 11, 2021
Reply
I was in contact with Razer support for about a week now before getting the usual response “sorry I checked, we don’t have any replacement parts” and basically told me to go &&^& myself and buy a new one.
I spent more than 100€ on this thing yet whenever I ask support ANYTHING it always boils down to this. This is the third time with three different Razer devices and I always get the same answer.
I’ll try this fix here and if that doesn’t work, this was surely the last time Razer got a single cent out of me.
If you’re not afraid of working with very small parts you can also try fixing the switch itself. You have to bend a small metal lip and that should fix the issue.
Here is a guide on how to do it, fixed my mouse with that one just half an hour ago.
https://www.youtube.com/watch?v=eDoXMJyi…
Jan - Oct 1, 2021
Reply
30-60 minutes? The author is liar! Took me 4 hours to complete just the step 15 “desolder the faulty switch” :D. For some reason I could not suck out all of the molten solder and it was always stuck somewhere. Really pain in the a**. Other parts of the guide made opening the mouse, disassembly and assembly rather very easy process. Soldering in new part as well. Transplantation is now complete and the patient survived. Thanks for the guide
