Razer Phone Charging Port Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          35 minutes

Sections

Display Assembly
6 steps
Battery
4 steps
Charging Port
4 steps

Flags

BackRazer Phone
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display Assembly

Remove the plastic speaker grills by using the metal spudger to pry underneath the strips.
Peel off the plastic speaker grill to reveal the screws.
Heating up the plastic grills make them easier to remove.
Peeling off the plastic speaker grill will ruin the adhesive used to keep it in place. A new adhesive must be used to put the grill back on the device.

Remove the plastic speaker grills by using the metal spudger to pry underneath the strips.

Peel off the plastic speaker grill to reveal the screws.

Heating up the plastic grills make them easier to remove.

Peeling off the plastic speaker grill will ruin the adhesive used to keep it in place. A new adhesive must be used to put the grill back on the device.

1024

Step 2

Pry the top plastic grill off with the metal spudger and reveal the screws.

Pry the top plastic grill off with the metal spudger and reveal the screws.

Step 3

Remove five (two bottom, three top) 2.5 mm screws with the Phillips #000 screwdriver.
Remove five (four bottom, one top) 5.5 mm screws with the Torx Head T5 screwdriver.

Remove five (two bottom, three top) 2.5 mm screws with the Phillips #000 screwdriver.

Remove five (four bottom, one top) 5.5 mm screws with the Torx Head T5 screwdriver.

Step 4

Remove the display assembly by using the Jimmy to separate the assembly from the phone’s frame.
Lift the display assembly away from the other half of the phone.

Remove the display assembly by using the Jimmy to separate the assembly from the phone’s frame.

Lift the display assembly away from the other half of the phone.

Step 5

Remove one 2.5 mm screw holding down the metal bracket connector using the Phillips #000 screwdriver.
Peel back the metallic shielding over the connector using tweezers.
Remove the metal bracket connector.

Remove one 2.5 mm screw holding down the metal bracket connector using the Phillips #000 screwdriver.

Peel back the metallic shielding over the connector using tweezers.

Remove the metal bracket connector.

Step 6

Grab hold of the the screen ribbon with the tweezers and remove it from the rest of the phone to free the assembly display.

Grab hold of the the screen ribbon with the tweezers and remove it from the rest of the phone to free the assembly display.

Step 7

              Battery

Grab hold of the connector on the right side of the phone (just above the battery) using the tweezers.
Remove the connector.

Grab hold of the connector on the right side of the phone (just above the battery) using the tweezers.

Remove the connector.

Step 8

Remove the 2.5 mm screw holding down the bracket with a Phillips #000 screwdriver.
Grab the bracket with the tweezers and remove it.

Remove the 2.5 mm screw holding down the bracket with a Phillips #000 screwdriver.

Grab the bracket with the tweezers and remove it.

Step 9

Peel off and pull out the elastic tabs at the bottom of the battery.

Peel off and pull out the elastic tabs at the bottom of the battery.

Step 10

Carefully use the Jimmy to wedge the battery out of the phone.

Carefully use the Jimmy to wedge the battery out of the phone.

Step 11

              Charging Port

Using a Phillips #000 screwdriver, take out the seven 1 mm screws on the bottom panel of the device.
There are a few gold brackets under some of the screws. Make sure to remove these and keep them for reassembly.

Using a Phillips #000 screwdriver, take out the seven 1 mm screws on the bottom panel of the device.

There are a few gold brackets under some of the screws. Make sure to remove these and keep them for reassembly.

Step 12

Grab hold of the blue connector on the upper left side of the phone with the tweezers.
Remove the connector.

Grab hold of the blue connector on the upper left side of the phone with the tweezers.

Step 13

Use the tweezers to grab hold of the connector for the blue wire (bottom of the device), and remove the connector.
Use the tweezers to grab hold of the connector for the white wire, and remove the connector.

Use the tweezers to grab hold of the connector for the blue wire (bottom of the device), and remove the connector.

Use the tweezers to grab hold of the connector for the white wire, and remove the connector.

Step 14

Using the tweezers, grab the detached charging port and ribbon.

Using the tweezers, grab the detached charging port and ribbon.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 2 other contributors

                    Bryan

Member since: 01/24/2019

601 Reputation

                                      2 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       Cal Poly, Team S19-G6, White Winter 2019                        

                                                  Member of Cal Poly, Team S19-G6, White Winter 2019 



                    CPSU-WHITE-W19S19G6                     


                                            5 Members                     


                                            12 Guides authored

Flims LP - Jun 16, 2019

Who i can find one replacement…pls a link

HolaSoy Guapo - Feb 12, 2020

johnny rodas - Jun 20, 2019

hi how much you guys charge for the charging port thanks

Derrick - May 26, 2020

Does this tutorial also work for the Razer phone 2?

victor balarezo - Jun 29, 2020

Does this work with the razor 2

Introduction#

What you need#

Team#

Introduction

What you need

Team