Difficulty

Easy

Steps

9

Time Required

                          10 minutes

Sections

2

  • Motherboard
  • 7 steps
  • Trigger Switches
  • 2 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackRazer Viper Mini

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove Information Sticker
  • Opening the mouse casing will void any warranty that exists for the mouse.
  • Make sure to unplug the mouse before doing anything.
  • Turn the Mouse Over so the bottom is facing up.
  • Remember to take a photo of your serial number or write it down
  • Take off the information sticker and the plastic cover from the bottom of the mouse.

Opening the mouse casing will void any warranty that exists for the mouse.

Make sure to unplug the mouse before doing anything.

Turn the Mouse Over so the bottom is facing up.

Remember to take a photo of your serial number or write it down

Take off the information sticker and the plastic cover from the bottom of the mouse.

1024

Step 2

              Remove Baseplate Screws
  • Use the Phillips #0 screwdriver to remove the three 2 mm screws from the bottom of the mouse.
  • When removing the screws, unscrew them each slightly and consecutively until you can pull them out with your hands.

Use the Phillips #0 screwdriver to remove the three 2 mm screws from the bottom of the mouse.

When removing the screws, unscrew them each slightly and consecutively until you can pull them out with your hands.

Step 3

              Detach backplate
  • Use the plastic spudger to gently lift the backplate from the mouse shell.
  • Insert the spudger into the bottom back of the mouse and slowly move it around the mouse to release the backplate.
  • Do not try to push or jab the mouse with the plastic spudger with a large amount of force, this can damage the plating of your mouse.

Use the plastic spudger to gently lift the backplate from the mouse shell.

Insert the spudger into the bottom back of the mouse and slowly move it around the mouse to release the backplate.

Do not try to push or jab the mouse with the plastic spudger with a large amount of force, this can damage the plating of your mouse.

Step 4

              Remove shell
  • Use the plastic spudger once again to remove the top shell of the mouse.
  • It is similar to the previous step, as you have to pry the plastic spudger gently into the bottom of the mouse and move it slowly inwards and upwards to release the shell.
  • Separating the casing too quickly could damage the ribbon connector between the motherboard and the cable.

Use the plastic spudger once again to remove the top shell of the mouse.

It is similar to the previous step, as you have to pry the plastic spudger gently into the bottom of the mouse and move it slowly inwards and upwards to release the shell.

Separating the casing too quickly could damage the ribbon connector between the motherboard and the cable.

Step 5

              Disconnect the Ribbon Connector
  • Disconnect the ribbon connector between the motherboard and the USB cable by squeezing the connector and pulling up.
  • Pulling too hard could damage the wire connections.
  • Pulling by the ribbon instead of the connector can dislocate the wires.

Disconnect the ribbon connector between the motherboard and the USB cable by squeezing the connector and pulling up.

Pulling too hard could damage the wire connections.

Pulling by the ribbon instead of the connector can dislocate the wires.

Step 6

              Unscrew Motherboard from Case
  • Use a Phillips #0 screwdriver to remove 2 5.5 and 3 2.5 mm screws.

Use a Phillips #0 screwdriver to remove 2 5.5 and 3 2.5 mm screws.

Step 7

              Remove Motherboard
  • Remove the motherboard by grasping the sides and gently pulling upward.

Remove the motherboard by grasping the sides and gently pulling upward.

Step 8

              Remove Left Switch
  • Press the connectors upwards to remove the left switch from the PCB.

Press the connectors upwards to remove the left switch from the PCB.

Step 9

              Remove Right Switch
  • Press the connectors upwards to remove the Right switch from the PCB.

Press the connectors upwards to remove the Right switch from the PCB.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor 


                    Addison

Member since: 08/30/2019

2,602 Reputation

                                      17 Guides authored                  



                       Badges:
                       20







                                                        +17 more badges

Team

                       University of North Texas, Team S1-G3, Friess Fall 2019                        

                                                  Member of University of North Texas, Team S1-G3, Friess Fall 2019 



                    UNT-FRIESS-F19S1G3                     


                                            3 Members                     


                                            34 Guides authored