Difficulty

Moderate

Steps

9

Time Required

                          10 minutes

Sections

2

  • Backplate
  • 4 steps
  • Battery
  • 5 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackRCA 10 Viking Pro RCT6K03W13

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Backplate
  • Remove the three Phillips #00 screws at the bottom of the device.

Remove the three Phillips #00 screws at the bottom of the device.

1024

Step 2

  • Remove the two Phillips #00 screws to the left and right of the keyboard connector.

Remove the two Phillips #00 screws to the left and right of the keyboard connector.

Step 3

  • Pull on one of the bottom corners to begin to pull off the back plate.

Pull on one of the bottom corners to begin to pull off the back plate.

Step 4

  • Work around the outside of the chassis, using the spudger to pry the backplate off.
  • After doing this for about half the device, the backplate should pop right off.

Work around the outside of the chassis, using the spudger to pry the backplate off.

After doing this for about half the device, the backplate should pop right off.

Step 5

              Battery
  • Remove the tape over the connectors on the motherboard and other side of the battery.

Remove the tape over the connectors on the motherboard and other side of the battery.

Step 6

  • Disconnect the red and black keyboard wires connecting the battery to the motherboard.

Disconnect the red and black keyboard wires connecting the battery to the motherboard.

Step 7

  • Disconnect the black ribbon cable running over the battery. Flip up the black clamp and pull the cable out.

Disconnect the black ribbon cable running over the battery. Flip up the black clamp and pull the cable out.

Step 8

  • Remove the cable over the battery connecting the motherboard and the power connector.
  • Flip up the black clamp and pull the cable out.

Remove the cable over the battery connecting the motherboard and the power connector.

Flip up the black clamp and pull the cable out.

Step 9

  • Pull out battery. It is taped to the device so it is safe to pull out.
  • Look for damage to the battery. If damaged, make sure to not get any acid on your fingers.

Pull out battery. It is taped to the device so it is safe to pull out.

Look for damage to the battery. If damaged, make sure to not get any acid on your fingers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      5 other people completed this guide.

Author

                                      with 2 other contributors 


                    Ryan Wickett

Member since: 10/25/2019

632 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       UMass Dartmouth, Team S1-G8, O'Connell Fall 2019                        

                                                  Member of UMass Dartmouth, Team S1-G8, O'Connell Fall 2019 



                    UMASSD-O'CONNELL-F19S1G8                     


                                            3 Members                     


                                            4 Guides authored

Justin - Feb 2, 2020

Reply

Where can I get the battery for this?

GLENDA Vandergrift - Mar 25, 2021

Jesus Rios - Jun 18, 2021

Reply

How much voltage should the battery put out in order for the tablet to turn on?

jennylyne_08 - Dec 5, 2021

Reply

How much