Difficulty
Easy
Steps
7
Time Required
10 - 15 minutes
Sections
2
- Disassembling RCA 22” DECK215R HDTV Stand and Back Panel
- 4 steps
- Button
- 3 steps
Flags
0
BackRCA DECK215R HDTV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing the Stand
- Before disassembling your television, ensure that all cables are unplugged from their power source to avoid serious injury or death from electrocution.
- Lay the TV flat with the screen facing down.
- Remove the four, 12mm Phillips #2 screws from the back of the TV stand. Support the TV from underneath as you remove the screws, so the bottom does not fall on the table.
- Remove the stand by lifting it away from the TV’s backing.
Before disassembling your television, ensure that all cables are unplugged from their power source to avoid serious injury or death from electrocution.
Lay the TV flat with the screen facing down.
Remove the four, 12mm Phillips #2 screws from the back of the TV stand. Support the TV from underneath as you remove the screws, so the bottom does not fall on the table.
Remove the stand by lifting it away from the TV’s backing.
1024
Step 2
Removing the Back Panel
- Remove the twelve, 6mm Phillips #2 screws from the middle of the TV’s rear casing.
- Remove the seven, 9mm Phillips #2 screws from the outer edge of the TV’s rear casing.
- While holding the screen down, pull the back panel up slowly, ensuring that you do not forcibly disconnect the remaining ribbon cable.
Remove the twelve, 6mm Phillips #2 screws from the middle of the TV’s rear casing.
Remove the seven, 9mm Phillips #2 screws from the outer edge of the TV’s rear casing.
While holding the screen down, pull the back panel up slowly, ensuring that you do not forcibly disconnect the remaining ribbon cable.
Step 3
Locate Pin
- Position the television to where the back panel is resting on the table and the screen is vertical.
- Peel the tape covering the ribbon cable horizontally.
Position the television to where the back panel is resting on the table and the screen is vertical.
Peel the tape covering the ribbon cable horizontally.
Step 4
- Pinch the clamps on both sides of the ribbon cable casing to detach it from the screen panel.
- Remove the screen to isolate the back panel.
Pinch the clamps on both sides of the ribbon cable casing to detach it from the screen panel.
Remove the screen to isolate the back panel.
Step 5
Button
- Locate the button circuit board on top of the TV plastic frame.
- Remove the blue and white ribbon cable connected to the circuit board by pulling with moderate to heavy force away from the circuit board.
Locate the button circuit board on top of the TV plastic frame.
Remove the blue and white ribbon cable connected to the circuit board by pulling with moderate to heavy force away from the circuit board.
Step 6
Locating the Top Buttons
- Remove the two 10mm Phillips #2 screws from the top of the button circuit board.
Remove the two 10mm Phillips #2 screws from the top of the button circuit board.
Step 7
- Lightly peel back the TV’s plastic frame, pressing down on the buttons from the outside.
- Holding this position, insert a plastic opening tool on top of the button circuit board.
- Apply forward pressure to pry out the circuit board and buttons from the frame.
Lightly peel back the TV’s plastic frame, pressing down on the buttons from the outside.
Holding this position, insert a plastic opening tool on top of the button circuit board.
Apply forward pressure to pry out the circuit board and buttons from the frame.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Patrick Soper
Member since: 01/15/2015
691 Reputation
6 Guides authored
Badges:
10
+7 more badges
Team
Cal Poly, Team 70-2, Forte Winter 2015
Member of Cal Poly, Team 70-2, Forte Winter 2015
CPSU-FORTE-W15S70G2
4 Members
10 Guides authored
