Difficulty

Easy

Steps

7

Time Required

                          15 minutes

Sections

2

  • Disassembling RCA 22” DECK215R HDTV Stand and Back Panel
  • 4 steps
  • Screen
  • 3 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackRCA DECK215R HDTV

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Removing the Stand
  • Before disassembling your television, ensure that all cables are unplugged from their power source to avoid serious injury or death from electrocution.
  • Lay the TV flat with the screen facing down.
  • Remove the four, 12mm Phillips #2 screws from the back of the TV stand. Support the TV from underneath as you remove the screws, so the bottom does not fall on the table.
  • Remove the stand by lifting it away from the TV’s backing.

Before disassembling your television, ensure that all cables are unplugged from their power source to avoid serious injury or death from electrocution.

Lay the TV flat with the screen facing down.

Remove the four, 12mm Phillips #2 screws from the back of the TV stand. Support the TV from underneath as you remove the screws, so the bottom does not fall on the table.

Remove the stand by lifting it away from the TV’s backing.

1024

Step 2

              Removing the Back Panel
  • Remove the twelve, 6mm Phillips #2 screws from the middle of the TV’s rear casing.
  • Remove the seven, 9mm Phillips #2 screws from the outer edge of the TV’s rear casing.
  • While holding the screen down, pull the back panel up slowly, ensuring that you do not forcibly disconnect the remaining ribbon cable.

Remove the twelve, 6mm Phillips #2 screws from the middle of the TV’s rear casing.

Remove the seven, 9mm Phillips #2 screws from the outer edge of the TV’s rear casing.

While holding the screen down, pull the back panel up slowly, ensuring that you do not forcibly disconnect the remaining ribbon cable.

Step 3

              Locate Pin
  • Position the television to where the back panel is resting on the table and the screen is vertical.
  • Peel the tape covering the ribbon cable horizontally.

Position the television to where the back panel is resting on the table and the screen is vertical.

Peel the tape covering the ribbon cable horizontally.

Step 4

  • Pinch the clamps on both sides of the ribbon cable casing to detach it from the screen panel.
  • Remove the screen to isolate the back panel.

Pinch the clamps on both sides of the ribbon cable casing to detach it from the screen panel.

Remove the screen to isolate the back panel.

Step 5

              Remove Screws
  • Remove the four, 12mm Phillips #2 screws from the outer edge of the back of the screen panel.

Remove the four, 12mm Phillips #2 screws from the outer edge of the back of the screen panel.

Step 6

              Remove the Screen from the Frame
  • Lift up the screen to remove it from the plastic frame.

Lift up the screen to remove it from the plastic frame.

Step 7

              Remove Brackets from the Side of the Screen
  • Remove the two, 5mm Phillips #2 screws from the metal bracket attached to the horizontal side of the TV and take the bracket off.
  • Repeat this process on the other side of the TV to completely isolate the screen.

Remove the two, 5mm Phillips #2 screws from the metal bracket attached to the horizontal side of the TV and take the bracket off.

Repeat this process on the other side of the TV to completely isolate the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 7 other contributors 


                    Patrick Soper

Member since: 01/15/2015

691 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 70-2, Forte Winter 2015                        

                                                  Member of Cal Poly, Team 70-2, Forte Winter 2015 



                    CPSU-FORTE-W15S70G2                     


                                            4 Members                     


                                            10 Guides authored