Difficulty
Moderate
Steps
14
Time Required
Suggest a time??
Sections
5
- Speaker
- 3 steps
- Camera
- 2 steps
- Power/Volume Buttons
- 1 step
- Battery
- 3 steps
- Display Screen
- 5 steps
Flags
3
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Better Introduction
Improve this guide by completing or revising its introduction.
BackRCA Atlas 10 PRO-S RCTS03W12H1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Speaker
- Using a separating tool, look for a seam in the plastic casing that looks most accessible.
- Use the prying tool to separate the front and back casing, working your way around the perimeter.
- Utilize a card tool or a pick to assist in keeping the case separated.
- To reassemble the device simply align the two casing halves and pinch to snap together or press down on the edges while the device in on a table.
Using a separating tool, look for a seam in the plastic casing that looks most accessible.
Use the prying tool to separate the front and back casing, working your way around the perimeter.
Utilize a card tool or a pick to assist in keeping the case separated.
To reassemble the device simply align the two casing halves and pinch to snap together or press down on the edges while the device in on a table.
1024
Step 2
- Flip over the back of the device while keeping it close to the front, the speaker is attached to it.
- Remove the yellow tape securing the speaker to the back casing.
Flip over the back of the device while keeping it close to the front, the speaker is attached to it.
Remove the yellow tape securing the speaker to the back casing.
Step 3
- Use the separating tool to pry the speaker from its surface.
- Use caution when removing the speaker, you may damage the screen.
- Cut or desolder the wires to replace or repair the speaker.
Use the separating tool to pry the speaker from its surface.
Use caution when removing the speaker, you may damage the screen.
Cut or desolder the wires to replace or repair the speaker.
Step 4
Camera
- Using a P00 Phillips screwdriver, remove the three screws securing the black plastic camera housing and remove it.
- Peel back the beige tape while holding down the camera ribbon cable to prevent tears
Using a P00 Phillips screwdriver, remove the three screws securing the black plastic camera housing and remove it.
Peel back the beige tape while holding down the camera ribbon cable to prevent tears
Step 5
- Lift the locking tab that is securing the camera ribbon cable.
- Slide the ribbon cable out from the connector and remove from casing.
Lift the locking tab that is securing the camera ribbon cable.
Slide the ribbon cable out from the connector and remove from casing.
Step 6
Power/Volume Buttons
- Use a P00 Phillips screwdriver to remove the three screws securing the button board.
- Desolder the contacts on the button board to remove or replace it.
Use a P00 Phillips screwdriver to remove the three screws securing the button board.
Desolder the contacts on the button board to remove or replace it.
Step 7
Battery
- Peel off the black tape on the battery and main-board.
- Peel off the black tape securing the screen ribbon cable to the back of the screen.
- Use caution to avoid damaging either ribbon cable.
Peel off the black tape on the battery and main-board.
Peel off the black tape securing the screen ribbon cable to the back of the screen.
Use caution to avoid damaging either ribbon cable.
Step 8
- Slide out the ribbon cable lock that is securing the screen ribbon cable.
- Move the ribbon cable out of the way using tape if necessary.
Slide out the ribbon cable lock that is securing the screen ribbon cable.
Move the ribbon cable out of the way using tape if necessary.
Step 9
- Remove the yellow tape securing the battery to the screen.
- Use a plastic card or pick to separate the battery from the screen.
- Do not bend or puncture battery, battery is difficult to separate from screen.
- Cut or desolder the wires on the battery to remove or replace it.
Remove the yellow tape securing the battery to the screen.
Use a plastic card or pick to separate the battery from the screen.
Do not bend or puncture battery, battery is difficult to separate from screen.
Cut or desolder the wires on the battery to remove or replace it.
Step 10
Display Screen
- Peel the WiFi antenna off of the monitor and move out of the way.
Peel the WiFi antenna off of the monitor and move out of the way.
Step 11
- Remove the black tape on the screen and the main-board.
- Lift the ribbon cable lock securing the digitizer ribbon cable.
- Slide out the digitizer ribbon cable and move away from the device, use tape to secure if necessary.
Remove the black tape on the screen and the main-board.
Lift the ribbon cable lock securing the digitizer ribbon cable.
Slide out the digitizer ribbon cable and move away from the device, use tape to secure if necessary.
Step 12
- Use a P00 Phillips screwdriver to remove the three screws securing the main-board to the back casing.
Use a P00 Phillips screwdriver to remove the three screws securing the main-board to the back casing.
Step 13
- Lift the main-board up and away from the ports to reveal the microphone.
- Use tweezers to remove the microphone from the black silicone.
- Move the main-board off the screen.
Lift the main-board up and away from the ports to reveal the microphone.
Use tweezers to remove the microphone from the black silicone.
Move the main-board off the screen.
Step 14
- Use a separator tool to lift the screen from the port side of the casing and remove it.
- To reassemble the device, follow these steps in reverse unless specified otherwise.
Use a separator tool to lift the screen from the port side of the casing and remove it.
To reassemble the device, follow these steps in reverse unless specified otherwise.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 3 other contributors
Tyler Schuster
Member since: 01/27/2015
461 Reputation
1 Guide authored
Badges:
9
+6 more badges
Team
Pasco Hernando, Team 1-1, Prince Winter 2015
Member of Pasco Hernando, Team 1-1, Prince Winter 2015
PHSC-PRINCE-W15S1G1
6 Members
10 Guides authored
Klaus laage - Sep 7, 2016
Reply
Gracias y ademas la buenas fotografias ayudaron una inmesidad.
Kl
Denise Engle - Feb 15, 2017
Reply
Nothing spectacular happened I just turned on my tablet today and voila! My display is crazed on part of the screen! I read these steps a couple times and I just don’t understand how if this process is intended to replace the display screen a display screen isn’t listed as a necessary part purchase. I have faith in reader generated sites so please help!
Chris Blackwell - Mar 27, 2017
Denise a new display screen would need to be purchased. Unless you absolutely have to have this particular tablet fixed I suggest buying a new one.
William Weygel - Jul 27, 2018
Reply
hola, podrás tener este repuesto de la pantalla lcd para la venta para ese modelo?
gracias
William Weygel
