Rca Rct6203W46 Rear Camera Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Front and Rear Camera
10 steps

Flags

BackRCA RCT6203W46
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front and Rear Camera

Make sure the device is off to reduce the chance of an electrical shock. To turn off the device, press and hold the power button.
Use a Phillips #00 Screwdriver to unscrew the 4mm (5/32 in.) screws from the back cover of the tablet.

Make sure the device is off to reduce the chance of an electrical shock. To turn off the device, press and hold the power button.

Use a Phillips #00 Screwdriver to unscrew the 4mm (5/32 in.) screws from the back cover of the tablet.

1024

Step 2

Use a spudger to pry the back cover. Start from one edge of the back cover and slide across until the cover is lifted from the tablet body. Repeat for all edges.

Use a spudger to pry the back cover. Start from one edge of the back cover and slide across until the cover is lifted from the tablet body. Repeat for all edges.

Step 3

Open the tablet cover carefully and slowly lengthwise.
The keyboard wire ribbon and rear speaker wire should be intact and connected with the back cover.
Opening the tablet abruptly may tear or damage cover attachments.

Open the tablet cover carefully and slowly lengthwise.

The keyboard wire ribbon and rear speaker wire should be intact and connected with the back cover.

Opening the tablet abruptly may tear or damage cover attachments.

Step 4

Use a spudger to flip up the flap of the ZIF connector that holds the keyboard wire ribbon.
Remove the wire ribbon from clamp.

Use a spudger to flip up the flap of the ZIF connector that holds the keyboard wire ribbon.

Remove the wire ribbon from clamp.

Step 5

Attached to the motherboard you will see two orange ribbons connected to black tabs.
Using both hands, place your thumbs gently on the black tab attached to the top and gently lift it.
Proceed to slide the orange colored ribbon out from underneath until it is detached from the black tab.

Attached to the motherboard you will see two orange ribbons connected to black tabs.

Using both hands, place your thumbs gently on the black tab attached to the top and gently lift it.

Proceed to slide the orange colored ribbon out from underneath until it is detached from the black tab.

Step 6

Use a spudger to pry and slide underneath the battery to unstick it from the LCD metal plate. It may take a good amount of force to remove.
Try to decrease battery deformation by using a spudger rather than prying with your hands.
Do not let battery fall back on adhesive, it will stick back onto the LCD metal plate.
Be careful to not puncture the battery. The battery may ignite or explode.

Use a spudger to pry and slide underneath the battery to unstick it from the LCD metal plate. It may take a good amount of force to remove.

Try to decrease battery deformation by using a spudger rather than prying with your hands.

Do not let battery fall back on adhesive, it will stick back onto the LCD metal plate.

Be careful to not puncture the battery. The battery may ignite or explode.

Step 7

Gently remove the grey tape that’s covering the grey colored wire until it is completely peeled off.
Peel off the black piece of tape to remove the antenna.

Gently remove the grey tape that’s covering the grey colored wire until it is completely peeled off.

Peel off the black piece of tape to remove the antenna.

Step 8

Unscrew three of the 4 mm screws on the motherboard using a Phillips #00 screwdriver.
After removing the screws, detach the motherboard from the rest of the tablet. Use a spudger to gently remove it, if necessary.

Unscrew three of the 4 mm screws on the motherboard using a Phillips #00 screwdriver.

After removing the screws, detach the motherboard from the rest of the tablet. Use a spudger to gently remove it, if necessary.

Step 9

Locate the rear camera and use a prying tool to gently lift the rear camera off of the motherboard.

Locate the rear camera and use a prying tool to gently lift the rear camera off of the motherboard.

Step 10

Detach the camera ribbon wire by lifting the tab and pulling the wire. This will leave you with the camera assembly.

Detach the camera ribbon wire by lifting the tab and pulling the wire. This will leave you with the camera assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Grace Chung

Member since: 09/21/2016

212 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       UC Davis, Team 1-2, Oliver Fall 2016                        

                                                  Member of UC Davis, Team 1-2, Oliver Fall 2016 



                    UCD-OLIVER-F16S1G2                     


                                            5 Members                     


                                            4 Guides authored

top - Oct 5, 2018

Where can I get the main board from RCT6203W46

Introduction#

What you need#

Team#

Introduction

What you need

Team