Difficulty

Moderate

Steps

11

Time Required

                          15 - 20 minutes

Sections

3

  • Battery
  • 2 steps
  • Speaker
  • 6 steps
  • Display
  • 3 steps

Flags

1

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackRCA RP3715A

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Reaching the battery terminal.
  • Push down on the clip to release pressure. The pull off the plastic cover.

Push down on the clip to release pressure. The pull off the plastic cover.

1024

Step 2

              Replacing the battery
  • Remove the 9-volt battery from the battery terminal.

Remove the 9-volt battery from the battery terminal.

Step 3

              Getting inside the device.
  • Take out the six screws located on the back of the device.
  • The red screws are 10 mm Phillip’s #1. The orange screws are 13 mm Phillips #1.
  • Three screws are located on the back panel. One is located inside the battery carriage.
  • Two screws are located on the on the back panel on the bottom left and right side.

Take out the six screws located on the back of the device.

The red screws are 10 mm Phillip’s #1. The orange screws are 13 mm Phillips #1.

Three screws are located on the back panel. One is located inside the battery carriage.

Two screws are located on the on the back panel on the bottom left and right side.

Step 4

              Relieve extension cord tension.
  • Remove the 10 mm Phillip’s #1 screw.
  • Then remove the metal reinforcement.

Remove the 10 mm Phillip’s #1 screw.

Then remove the metal reinforcement.

Step 5

  • Using flathead screwdriver undo the release tabs.

Using flathead screwdriver undo the release tabs.

Step 6

  • Pry the release tabs with a spudger.
  • Start with back of the device on the topside.

Pry the release tabs with a spudger.

Start with back of the device on the topside.

Step 7

  • Pry open both tabs to remove the topside of the clock.

Pry open both tabs to remove the topside of the clock.

Step 8

              Speaker Replacement
  • Remove the two 10mm Phillip’s #1 screws. Also remove the two reinforcements holding the speaker in place.

Remove the two 10mm Phillip’s #1 screws. Also remove the two reinforcements holding the speaker in place.

Step 9

              Detaching the front panel
  • Remove the two 10 mm Phillip’s #1 screws.

Remove the two 10 mm Phillip’s #1 screws.

Step 10

  • Remove the gray panel from the frame.

Remove the gray panel from the frame.

Step 11

              Unlatch release tabs
  • The two latches located in the picture will help take off the display.
  • Remove the display.

The two latches located in the picture will help take off the display.

Remove the display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors 


                    Myles Waiters

Member since: 09/22/2014

370 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team 10-5, Brown Fall 2014                        

                                                  Member of USF Tampa, Team 10-5, Brown Fall 2014 



                    USFT-BROWN-F14S10G5                     


                                            3 Members                     


                                            5 Guides authored