Difficulty
Moderate
Steps
16
Time Required
15 - 30 minutes
Sections
3
- Speaker
- 6 steps
- Display
- 3 steps
- Motherboard
- 7 steps
Flags
2
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Slice and Dice
The steps in this guide should be split up and made into a series of prerequisite guides.
BackRCA RP3715A
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Getting inside the device.
- Take out the six screws located on the back of the device.
- The red screws are 10 mm Phillip’s #1. The orange screws are 13 mm Phillips #1.
- Three screws are located on the back panel. One is located inside the battery carriage.
- Two screws are located on the on the back panel on the bottom left and right side.
Take out the six screws located on the back of the device.
The red screws are 10 mm Phillip’s #1. The orange screws are 13 mm Phillips #1.
Three screws are located on the back panel. One is located inside the battery carriage.
Two screws are located on the on the back panel on the bottom left and right side.
1024
Step 2
Relieve extension cord tension.
- Remove the 10 mm Phillip’s #1 screw.
- Then remove the metal reinforcement.
Remove the 10 mm Phillip’s #1 screw.
Then remove the metal reinforcement.
Step 3
- Using flathead screwdriver undo the release tabs.
Using flathead screwdriver undo the release tabs.
Step 4
- Pry the release tabs with a spudger.
- Start with back of the device on the topside.
Pry the release tabs with a spudger.
Start with back of the device on the topside.
Step 5
- Pry open both tabs to remove the topside of the clock.
Pry open both tabs to remove the topside of the clock.
Step 6
Speaker Replacement
- Remove the two 10mm Phillip’s #1 screws. Also remove the two reinforcements holding the speaker in place.
Remove the two 10mm Phillip’s #1 screws. Also remove the two reinforcements holding the speaker in place.
Step 7
Detaching the front panel
- Remove the two 10 mm Phillip’s #1 screws.
Remove the two 10 mm Phillip’s #1 screws.
Step 8
- Remove the gray panel from the frame.
Remove the gray panel from the frame.
Step 9
Unlatch release tabs
- The two latches located in the picture will help take off the display.
- Remove the display.
The two latches located in the picture will help take off the display.
Remove the display.
Step 10
Motherboard
- asd
asd
Step 11
Removing the top part of motherboard
- Remove the top 5 10mm Phillips #1 screws holding the top part of the motherboard
Remove the top 5 10mm Phillips #1 screws holding the top part of the motherboard
Step 12
Removing the side part of motherboard
- Remove the 5 10mm Phillip’s #1 screws that holding side part of the motherboard
Remove the 5 10mm Phillip’s #1 screws that holding side part of the motherboard
Step 13
- Remove the transformer by pulling back the release tab shown.
Remove the transformer by pulling back the release tab shown.
Step 14
- Pull the battery terminal through the whole shown.
Pull the battery terminal through the whole shown.
Step 15
Lift the digital screen
- First release the latch highlighted in the picture. Then grab the screen by the bottom and lift it up.
First release the latch highlighted in the picture. Then grab the screen by the bottom and lift it up.
Step 16
Lift the top piece of motherboard
- Remove the motherboard from the frame using the illustration shown.
Remove the motherboard from the frame using the illustration shown.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Alexander Trowell
Member since: 09/22/2014
222 Reputation
2 Guides authored
Badges:
6
+3 more badges
Team
USF Tampa, Team 10-5, Brown Fall 2014
Member of USF Tampa, Team 10-5, Brown Fall 2014
USFT-BROWN-F14S10G5
3 Members
5 Guides authored
