Difficulty

Moderate

Steps

17

Time Required

                          10 minutes

Sections

1

  • RCA Voyager II RCT6773W22 Disassembly
  • 17 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackRCA Voyager II

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Note that the tablet pictured has been disassembled and reassembled before.

What you need

Step 1

              RCA Voyager II RCT6773W22 Disassembly
  • Have Workstation Prepped

Have Workstation Prepped

1024

Step 2

  • remove the two screws on the top of the device with a PH000 screwdriver

remove the two screws on the top of the device with a PH000 screwdriver

Step 3

  • Starting from the top, place pick or plastic tool between the power button and screen edge and push apart slightly.

Starting from the top, place pick or plastic tool between the power button and screen edge and push apart slightly.

Step 4

  • Run pick across the top to the right and then down the right side and around the rest of the tablet.
  • There is a good amount of space between the bezel and the board. Be gentle, but the risk of breaking components is low.

Run pick across the top to the right and then down the right side and around the rest of the tablet.

There is a good amount of space between the bezel and the board. Be gentle, but the risk of breaking components is low.

Step 5

  • lift section out of the black casing from the bottom, lift and remove by pulling away from tablet.

lift section out of the black casing from the bottom, lift and remove by pulling away from tablet.

Step 6

  • Battery connection (on older models, may be soldered to board)
  • Front Camera
  • Digitizer
  • LCD
  • Speaker

Battery connection (on older models, may be soldered to board)

Front Camera

Digitizer

LCD

Speaker

Step 7

  • Remove battery Connection First
  • Do not use any metal tools while the battery is plugged in. It may cause a short.

Remove battery Connection First

Do not use any metal tools while the battery is plugged in. It may cause a short.

Step 8

  • unplug the speaker

unplug the speaker

Step 9

  • Lift the black cover over all three flex cables (Camera, LCD, Digitizer) with a plastic tool.
  • The covers are incredibly fragile, and easy to break
  • gently disconnect all three cables with your fingers by pulling slightly

Lift the black cover over all three flex cables (Camera, LCD, Digitizer) with a plastic tool.

The covers are incredibly fragile, and easy to break

gently disconnect all three cables with your fingers by pulling slightly

Step 10

  • remove the three screws securing the board with your PH000 Screwdriver

remove the three screws securing the board with your PH000 Screwdriver

Step 11

  • lift the board out gently
  • Do not tug the board out too hard, the antenna cable on the left is soldered in!
  • Fold board over the left side of the tablet and gently remove tape securing antenna to the case. Use a small amount of heat if necessary.

lift the board out gently

Do not tug the board out too hard, the antenna cable on the left is soldered in!

Fold board over the left side of the tablet and gently remove tape securing antenna to the case. Use a small amount of heat if necessary.

Step 12

  • remove tape from top and bottom of the battery.
  • with a plastic piece, lift battery from adhesive securing it in place.
  • do not use a metal or sharp tool to remove the battery, tearing or puncturing it may cause it to explode or heat rapidly, and may damage your device.
  • The battery is secured directly to the back of the LCD. Exercise caution while removing the battery not to damage the LCD.
  • The battery is soft and somewhat malleable - it can bend slightly without damage.

remove tape from top and bottom of the battery.

with a plastic piece, lift battery from adhesive securing it in place.

do not use a metal or sharp tool to remove the battery, tearing or puncturing it may cause it to explode or heat rapidly, and may damage your device.

The battery is secured directly to the back of the LCD. Exercise caution while removing the battery not to damage the LCD.

The battery is soft and somewhat malleable - it can bend slightly without damage.

Step 13

  • Place picks between the lcd and the plastic clips holding it in place.
  • The pick placement to the top left side (near the power button) is smaller and on a corner. I recommend inserting this pick last.

Place picks between the lcd and the plastic clips holding it in place.

The pick placement to the top left side (near the power button) is smaller and on a corner. I recommend inserting this pick last.

Step 14

  • Gently push top right pick down to lift LCD from the clip. Run across the top and right side to further lift LCD.
  • Use picks as needed to separate LCD in other areas.

Gently push top right pick down to lift LCD from the clip. Run across the top and right side to further lift LCD.

Use picks as needed to separate LCD in other areas.

Step 15

  • Once separated and loose, remove picks so you do not damage the LCD while removing it.
  • To remove, lift top of LCD and pull out of case away from the speaker, which is fixed to the digitizer frame.

Once separated and loose, remove picks so you do not damage the LCD while removing it.

To remove, lift top of LCD and pull out of case away from the speaker, which is fixed to the digitizer frame.

Step 16

  • to remove Digitizer/Glass from the frame and speaker, slide a pick under a corner between the glass and frame to loosen adhesive
  • If you’re having issues loosening the adhesive, use a heat gun around the edges, then try again.

to remove Digitizer/Glass from the frame and speaker, slide a pick under a corner between the glass and frame to loosen adhesive

If you’re having issues loosening the adhesive, use a heat gun around the edges, then try again.

Step 17

  • You have completely dismantled the RCA Voyager II

You have completely dismantled the RCA Voyager II

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      34 other people completed this guide.

Author

                                      with 2 other contributors 


                    Chris

Member since: 01/11/2016

1,992 Reputation

                                      1 Guide authored                  



                       Badges:
                       13







                                                        +10 more badges

TheUnchanted Sword - Jul 11, 2016

Reply

what is that flat part that has the little copper bar in the middle. What do you call that?

Sam Goldheart - Jul 12, 2016

The LCD has a piece of copper tape on it, is that what you mean?

Aerial L - Nov 12, 2016

Reply

Nice Guide. Very Simple and Easy to follow!

diego jamal - Dec 2, 2016

Reply

Bonne site merci pour tous je suis très heureux content que entrer dans ce site

Spock Chen - Dec 15, 2016

Reply

Anyone know which company made this very fragile digitizer for RCA Voyager?