Difficulty
Moderate
Steps
6
Time Required
1 - 3 minutes
Sections
3
- Battery
- 2 steps
- Front Casing
- 2 steps
- Rear Casing
- 2 steps
Flags
1
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
BackOlympus FE-210
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- The battery compartment is located on the bottom side of the camera. Push the button in, and slide the cover to get access to the batteries.
The battery compartment is located on the bottom side of the camera. Push the button in, and slide the cover to get access to the batteries.
1024
Step 2
- The batteries will slide right out.
- When putting new batteries in, make sure they are pointing the right direction.
The batteries will slide right out.
When putting new batteries in, make sure they are pointing the right direction.
Step 3
Front Casing
- Remove the 7 screws holding the front case in place, with a #00 screwdriver.
- Six screws are 3.6 mm.
- The seventh screw is 3.2 mm.
Remove the 7 screws holding the front case in place, with a #00 screwdriver.
Six screws are 3.6 mm.
The seventh screw is 3.2 mm.
Step 4
- Pulling the front case off, requires applying enough strength in the right areas.
- The front case snaps into place in three places:
- At the top and bottom of the battery side (opposite of side pictured) of the case.
- Right in the middle of the DC-in side (side pictured) of the case.
- Top of the camera, to the left of the power button.
- Once those places are disconnected, the front case will pop right off.
- The camera in the first two pictures is upside down. This is the best position to place your thumbs to remove the case.
Pulling the front case off, requires applying enough strength in the right areas.
The front case snaps into place in three places:
At the top and bottom of the battery side (opposite of side pictured) of the case.
Right in the middle of the DC-in side (side pictured) of the case.
Top of the camera, to the left of the power button.
Once those places are disconnected, the front case will pop right off.
The camera in the first two pictures is upside down. This is the best position to place your thumbs to remove the case.
Step 5
Rear Casing
- Remove the 3.2 mm screw in the battery compartment using a #00 screwdriver.
- After removal of the screw the case will be loose, but do not tug it off. There is a cord connecting the rear controls to the motherboard.
Remove the 3.2 mm screw in the battery compartment using a #00 screwdriver.
After removal of the screw the case will be loose, but do not tug it off. There is a cord connecting the rear controls to the motherboard.
Step 6
- Carefully pull the rear case away from the camera until you have access to the cord connected to the motherboard.
- Lift the white latch using a fingernail or a spudger.
- Pull the cord from its connector.
Carefully pull the rear case away from the camera until you have access to the cord connected to the motherboard.
Lift the white latch using a fingernail or a spudger.
Pull the cord from its connector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Matt
Member since: 01/25/2011
781 Reputation
6 Guides authored
Badges:
8
+5 more badges
Team
Cal Poly, Team 4-36, Regan Winter 2011
Member of Cal Poly, Team 4-36, Regan Winter 2011
CPSU-REGAN-W11S4G36
3 Members
14 Guides authored
