Difficulty
Moderate
Steps
10
Time Required
45 minutes
Sections
4
- Battery Removal
- 1 step
- Keyboard
- 3 steps
- Switch Cover
- 2 steps
- Display Assembly
- 4 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackHP Elitebook 6930p
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery Removal
- Flip laptop over and locate the battery release button
- Push release button to the left to release battery and gently pull battery from the laptop
Flip laptop over and locate the battery release button
Push release button to the left to release battery and gently pull battery from the laptop
1024
Step 2
Keyboard
- Loosen the three Phillips 2.5×9.0 captive screws that secure the keyboard to the laptop
- Turn the laptop so the keyboard is facing up and locate the 4 retention tabs along the back edge of the keyboard
- Slide the retention clips toward the keyboard to release the keyboard
Loosen the three Phillips 2.5×9.0 captive screws that secure the keyboard to the laptop
Turn the laptop so the keyboard is facing up and locate the 4 retention tabs along the back edge of the keyboard
Slide the retention clips toward the keyboard to release the keyboard
Step 3
- Use a plastic pry tool to lift the rear edge of the keyboard.
- Pull the keyboard slightly towards the display to disengage the tabs along the front of the keyboard from the laptop palm rest.
- Lift the keyboard up to reveal the ribbon connectors
Use a plastic pry tool to lift the rear edge of the keyboard.
Pull the keyboard slightly towards the display to disengage the tabs along the front of the keyboard from the laptop palm rest.
Lift the keyboard up to reveal the ribbon connectors
Step 4
- Release the larger ribbon cable by flipping the brown retainer up so it is parallel with the ribbon cable
- Release the smaller ribbon cable by lifting up the white retainer
- I found it easier to reinstall both cables with the new keyboard resting on the back edge
Release the larger ribbon cable by flipping the brown retainer up so it is parallel with the ribbon cable
Release the smaller ribbon cable by lifting up the white retainer
I found it easier to reinstall both cables with the new keyboard resting on the back edge
Step 5
Switch Cover
- Remove the two M2.0×4.0 broad-head screws.
- Remove the three Torx T8 M2.5×7.0 screws.
Remove the two M2.0×4.0 broad-head screws.
Remove the three Torx T8 M2.5×7.0 screws.
Step 6
- Turn the computer over with the front toward you and the open the computer as far as possible.
- Release the ZIF connector for the power button board cable.
- Remove the switch cover by lifting it straight up and flip it forward.
- Release the ZIF connector for the LED board cable.
Turn the computer over with the front toward you and the open the computer as far as possible.
Release the ZIF connector for the power button board cable.
Remove the switch cover by lifting it straight up and flip it forward.
Release the ZIF connector for the LED board cable.
Step 7
Display Assembly
- Close the lid and turn the laptop so the rear is facing you
- Locate and remove the two Torx T8 2.5×7.0 screws at each corner
- The screws may have rubber caps over them. If so remove with a spudger or similar tool.
Close the lid and turn the laptop so the rear is facing you
Locate and remove the two Torx T8 2.5×7.0 screws at each corner
The screws may have rubber caps over them. If so remove with a spudger or similar tool.
Step 8
- With the laptop upside down, locate and remove the two Torx T8 2.5×7.0 screws.
- The screws may have rubber caps over them. If so remove with a spudger or similar tool.
With the laptop upside down, locate and remove the two Torx T8 2.5×7.0 screws.
Step 9
- Turn the computer right-side up with the front toward you and open the computer lid past 90 degrees.
- Locate and disconnect the display panel cable.
- Locate and disconnect the microphone cable.
- Locate and disconnect the webcam cable.
- Locate and disconnect the 3 antenna cables.
- Unclip the antenna cables from the retaining clips.
- NOTE There are 2 antenna cables that go from the display assembly through the hole shown and connect to the WWAN (3G) WiFi card if it is installed. In my case they were just threaded into the hole to make things tidy as I didn’t have a WWAN card.
Turn the computer right-side up with the front toward you and open the computer lid past 90 degrees.
Locate and disconnect the display panel cable.
Locate and disconnect the microphone cable.
Locate and disconnect the webcam cable.
Locate and disconnect the 3 antenna cables.
Unclip the antenna cables from the retaining clips.
NOTE There are 2 antenna cables that go from the display assembly through the hole shown and connect to the WWAN (3G) WiFi card if it is installed. In my case they were just threaded into the hole to make things tidy as I didn’t have a WWAN card.
Step 10
- The display assembly will be unsupported when the following screws are removed. To prevent damage support the display before removing the screws.
- Remove the two T8 2.5×7.0 screws holding the display assembly to the laptop.
- Lift the display assembly straight up to remove it from the laptop.
The display assembly will be unsupported when the following screws are removed. To prevent damage support the display before removing the screws.
Remove the two T8 2.5×7.0 screws holding the display assembly to the laptop.
Lift the display assembly straight up to remove it from the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
11 other people completed this guide.
Author
with 1 other contributor
Richdave
Member since: 04/09/2010
31,742 Reputation
30 Guides authored
Badges:
51
+48 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored
Emilio Zelaya - Feb 26, 2016
Reply
muy útil el aporte
