Difficulty

Moderate

Steps

17

Time Required

Suggest a time??

Sections

4

  • Battery
  • 2 steps
  • Outer Casing
  • 8 steps
  • LCD Assembly
  • 4 steps
  • LCD
  • 3 steps

Flags

0

  • BackSony Cyber-shot DSC-W290

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Find the hatch labeled “open” on the left side of the bottom of the camera.
  • Slide the hatch in the direction that the arrow is pointing. The hatch will open outward on its own.

Find the hatch labeled “open” on the left side of the bottom of the camera.

Slide the hatch in the direction that the arrow is pointing. The hatch will open outward on its own.

1024

Step 2

  • Slide the blue locking tab to release the battery.
  • Slide the battery out of the camera.

Slide the blue locking tab to release the battery.

Slide the battery out of the camera.

Step 3

              Outer Casing
  • Replace hatch and rotate camera 180 degrees. You should still be looking at the bottom of the camera.
  • Remove the four 2.5mm Phillips #0 screws.

Replace hatch and rotate camera 180 degrees. You should still be looking at the bottom of the camera.

Remove the four 2.5mm Phillips #0 screws.

Step 4

  • Turn the camera so the left side-panel reading “5x Optical Zoom” faces you.
  • Remove the two 2.5mm Phillips #0 screws.
  • You may have to remove the screws with a pair of tweezers when the screws are almost out.

Turn the camera so the left side-panel reading “5x Optical Zoom” faces you.

Remove the two 2.5mm Phillips #0 screws.

You may have to remove the screws with a pair of tweezers when the screws are almost out.

Step 5

  • Turn the camera so the right side faces you.
  • Remove the two 2.5mm Phillips #0 screws.
  • You may have to remove the screws with a pair of tweezers when the screws are almost out.

Turn the camera so the right side faces you.

Step 6

  • Rotate camera so that the back is facing you.
  • Pull the back casing directly away from the LCD screen.

Rotate camera so that the back is facing you.

Pull the back casing directly away from the LCD screen.

Step 7

  • Turn the camera so that the left side is facing you.
  • Pull the left side-panel off of the camera.

Turn the camera so that the left side is facing you.

Pull the left side-panel off of the camera.

Step 8

  • Turn camera so that the front of the camera is facing you.
  • Pull the front casing directly away from the camera.
  • The right side panel may fall off when you take the front panel off.

Turn camera so that the front of the camera is facing you.

Pull the front casing directly away from the camera.

The right side panel may fall off when you take the front panel off.

Step 9

  • Turn the camera so that the right side is facing you.
  • Pull the right side-panel away from the rest of the camera.

Turn the camera so that the right side is facing you.

Pull the right side-panel away from the rest of the camera.

Step 10

  • This is what your camera should look like now that you have removed the casing from all sides.

This is what your camera should look like now that you have removed the casing from all sides.

Step 11

              LCD Assembly
  • Gently pull the LCD and its casing away from the motherboard as shown.
  • Be careful not to rip out any ribbon cables.

Gently pull the LCD and its casing away from the motherboard as shown.

Be careful not to rip out any ribbon cables.

Step 12

  • Disconnect the small ribbon-wire by gently pulling on the small ribbon-wire where it connects with the motherboard.
  • Do not use excessive force to remove the wire because this may cause it to tear.

Disconnect the small ribbon-wire by gently pulling on the small ribbon-wire where it connects with the motherboard.

Do not use excessive force to remove the wire because this may cause it to tear.

Step 13

  • Disconnect the large ribbon-wire by pulling on the large ribbon-wire where it connects to the motherboard.

Disconnect the large ribbon-wire by pulling on the large ribbon-wire where it connects to the motherboard.

Step 14

  • Pull the LCD and its casing away from the rest of the camera.

Pull the LCD and its casing away from the rest of the camera.

Step 15

              LCD
  • Rotate the LCD and its casing so that the screen is facing you.
  • Gently pull the control panel downward, freeing it from the small metal clips.
  • Lift the control panel away from the metal and carefully pull the ribbon-wire out as you do.

Rotate the LCD and its casing so that the screen is facing you.

Gently pull the control panel downward, freeing it from the small metal clips.

Lift the control panel away from the metal and carefully pull the ribbon-wire out as you do.

Step 16

  • Lift the LCD away from the metal casing on the right side.
  • Slide the LCD to the right and away from the metal casing.
  • Carefully pull the ribbon-wire out of the opening in the metal casing.

Lift the LCD away from the metal casing on the right side.

Slide the LCD to the right and away from the metal casing.

Carefully pull the ribbon-wire out of the opening in the metal casing.

Step 17

  • The LCD is now out of the camera.

The LCD is now out of the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    William Schill

Member since: 10/04/2010

222 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Cal Poly, Team 7-54, Amido Fall 2010                        

                                                  Member of Cal Poly, Team 7-54, Amido Fall 2010 



                    CPSU-AMIDO-F10S7G54                     


                                            4 Members                     


                                            16 Guides authored

miguel - Jul 29, 2012

Reply

donde puedo conseguir la pantalla? porque la mia se estrello :(