Repairing Vtech Touch And Swipe Baby Phone Screen Alignment Repair Guide

Difficulty

Moderate

Steps

12

Time Required

Suggest a time??

Sections

2

• Battery
• 3 steps
• Repairing VTech Touch and Swipe Baby Phone Screen Alignment
• 9 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

Missing Details

Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.

• BackVTech Touch and Swipe Baby Phone

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Using a Phillips #1 screwdriver, remove the 4.8mm screw on the battery cover by twisting the screwdriver counter-clockwise.

Using a Phillips #1 screwdriver, remove the 4.8mm screw on the battery cover by twisting the screwdriver counter-clockwise.

1024

Step 2

• Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.

Remove the two AAA batteries by pulling on one end of the battery and lifting it straight out.

Step 3

• When reassembling, align the notch on the battery panel with the slot on the phone.

When reassembling, align the notch on the battery panel with the slot on the phone.

Step 4

              Repairing VTech Touch and Swipe Baby Phone Screen Alignment               

• Remove four 13.8mm screws from the back of the device using a Phillips #1 screwdriver.

Remove four 13.8mm screws from the back of the device using a Phillips #1 screwdriver.

Step 5

• Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires.

Remove a single 4.8 mm screw with a Phillips #0 screwdriver and lift away the battery pack being careful of the wires.

Step 6

• Remove two 7.2 mm screws with a Phillips #0 screwdriver.
• Slide off the spring.

Remove two 7.2 mm screws with a Phillips #0 screwdriver.

Slide off the spring.

Step 7

• Remove the single 7.5mm screw with a Phillips #0 screwdriver.
• Lift up the black plastic piece.

Remove the single 7.5mm screw with a Phillips #0 screwdriver.

Lift up the black plastic piece.

Step 8

• Remove four 7.5mm screws with a Phillips #0 screwdriver.

Remove four 7.5mm screws with a Phillips #0 screwdriver.

Step 9

• Remove the two buttons, noting how wires are placed for reassembly.

Remove the two buttons, noting how wires are placed for reassembly.

Step 10

• Lift the button board up and away to clear room for lifting the motherboard.
• Tilt the assembly up but being wary that it is still attached to the front panel.

Lift the button board up and away to clear room for lifting the motherboard.

Tilt the assembly up but being wary that it is still attached to the front panel.

Step 11

• Slide the toothed slider towards you to remove.

Slide the toothed slider towards you to remove.

Step 12

• To reassemble, align the two black lines together by moving the belt back and forth.
• Once aligned reinsert the toothed slider at the exact point shown.

To reassemble, align the two black lines together by moving the belt back and forth.

Once aligned reinsert the toothed slider at the exact point shown.

To reassemble your device, follow these instructions in reverse order, skipping step 10 as the toothed slider has already been put in for proper alignment.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 3 other contributors 

                    Sean Webb                     

Member since: 09/04/2015

384 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       USF Tampa, Team 2-4, Sullivan Fall 2015                        

                                                  Member of USF Tampa, Team 2-4, Sullivan Fall 2015 



                    USFT-SULLIVAN-F15S2G4                     


                                            3 Members                     


                                            6 Guides authored                     

Schwarzstein - Jul 21, 2016

Reply

Good work !

Nice.

I did not see the black line in mine,

i opened the foil and glued it new together . Not so nice. :D

But it works.