Difficulty

Moderate

Steps

3

Time Required

                          15 minutes

Sections

  • Back panel
  • 1 step
  • Battery
  • 1 step
  • Port Jack
  • 1 step

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackDell XPS 13 9380 (2019)

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the back panel
  • Before you begin, be sure to turn off your laptop and unplug it from the outlet.
  • Use a Torx T5 driver to unscrew the eight screws securing the back panel.
  • Use a spudger to pry up and loosen the back panel.
  • Lift the back panel up slightly from the non-hinged edge.
  • Pull the back panel away from the hinged edge, wiggling it back and forth to loosen the clips.
  • When the back panel clips are free, remove the back panel.

Before you begin, be sure to turn off your laptop and unplug it from the outlet.

Use a Torx T5 driver to unscrew the eight screws securing the back panel.

Use a spudger to pry up and loosen the back panel.

Lift the back panel up slightly from the non-hinged edge.

Pull the back panel away from the hinged edge, wiggling it back and forth to loosen the clips.

When the back panel clips are free, remove the back panel.

1024

Step 2

              Remove the battery
  • Disconnect the cable from the battery by pulling the connector towards the battery.
  • Pull parallel to the battery, not straight up.
  • Remove the four screws (M2 x 2) securing the battery.
  • Remove the screw (M1.6 x 4) securing the battery.
  • Remove the battery from its recess.

Disconnect the cable from the battery by pulling the connector towards the battery.

Pull parallel to the battery, not straight up.

Remove the four screws (M2 x 2) securing the battery.

Remove the screw (M1.6 x 4) securing the battery.

Remove the battery from its recess.

Step 3

              Port Jack
  • 1- Remove the two screws (M2.5 x 4) that fix the left hinge.
  • 2- Place the back of the computer screen on a clean and flat surface, then open and close the computer.
  • 3- Disconnect the cable from the Jack port of the motherboard.
  • 4- Remove the screw (M1,6x3) that fixes the jack port.
  • 5- Remove the Jack port.

1- Remove the two screws (M2.5 x 4) that fix the left hinge.

2- Place the back of the computer screen on a clean and flat surface, then open and close the computer.

3- Disconnect the cable from the Jack port of the motherboard.

4- Remove the screw (M1,6x3) that fixes the jack port.

5- Remove the Jack port.

To reassemble your device, follow the instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        Schwarzer is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Schwarzer

Author

                                      with 1 other contributor 


                    Schwarzer

Member since: 08/07/2019

4,604 Reputation

                                      13 Guides authored                  



                       Badges:
                       33







                                                        +30 more badges

Team

                       i.Fixit FR Team                        

                                                  Member of i.Fixit FR Team 



                    Community                     


                                            3 Members                     


                                            35 Guides authored

Todd Resudek - Mar 12, 2020

Reply

Where did you get the replacement part?