Difficulty
Easy
Steps
11
Time Required
10 - 15 minutes
Sections
2
- Outer Shell Removal
- 5 steps
- Bread Lift Shelf
- 6 steps
Flags
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Better Introduction
Improve this guide by completing or revising its introduction.
BackOster 6329
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Outer Shell Removal
- Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.
Using the Phillips-head #2 screwdriver, unscrew the three 1cm Phillips-head screws on the plastic base of the toaster to separate the outer metal shell from the plastic base.
1024
Step 2
- Push the plastic push-down handle down and pull the plastic handle straight from metal arm.
Push the plastic push-down handle down and pull the plastic handle straight from metal arm.
Step 3
- Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.
- Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.
Loosen the outer metal shell from the plastic base by holding the plastic base while pulling up on the metal shell.
Only lift the outer shell a little so as not to disconnect the cables that connect the circuit board.
Step 4
- Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.
Disconnect the cable clips from the circuit board using the tweezers to free the outer metal shell from the plastic base.
Step 5
- Lift the top outer metal shell.
- Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.
Lift the top outer metal shell.
Carefully lift the outer metal shell at an angle so as not to damage the components in the front of the toaster.
Step 6
Bread Lift Shelf
- Use a flat-head screwdriver to separate the metal flap from the metal plate.
Use a flat-head screwdriver to separate the metal flap from the metal plate.
Step 7
- Grasp the metal flap with the large needle nose pliers.
- Unbend metal flap until at a 90 degree angle from the metal plate.
- Repeat these steps for the second metal flap.
Grasp the metal flap with the large needle nose pliers.
Unbend metal flap until at a 90 degree angle from the metal plate.
Repeat these steps for the second metal flap.
Step 8
- Use the large need nose pliers to grab the metal panel.
- Pull the metal panel away from the body of the toaster to dislodge the flaps.
Use the large need nose pliers to grab the metal panel.
Pull the metal panel away from the body of the toaster to dislodge the flaps.
Step 9
- Push the metal flaps towards the body of the toaster to access the bread lift shelf.
Push the metal flaps towards the body of the toaster to access the bread lift shelf.
Step 10
- Push down on the opposite side of the bread lift shelf to expose the metal flaps.
Push down on the opposite side of the bread lift shelf to expose the metal flaps.
Step 11
- Pull up on the bread lift shelf to remove from the toaster.
Pull up on the bread lift shelf to remove from the toaster.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Jason Yoon
Member since: 01/31/2014
101 Reputation
1 Guide authored
Badges:
3
Team
Cal Poly, Team 13-15, Regan Winter 2014
Member of Cal Poly, Team 13-15, Regan Winter 2014
CPSU-REGAN-W14S13G15
5 Members
6 Guides authored
