Revlon One Step Hair Dryer Air Inlet Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          20 minutes            

Sections

5

• Barrel
• 3 steps
• Cord and Plug
• 4 steps
• Setting Dial
• 1 step
• Lint Filter
• 2 steps
• Air Inlet
• 1 step

Flags

0

• BackRevlon One-Step Hair Dryer

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Barrel               

• First, remove the pink panels on each side of the handle in order to access the screws.
• Use the iFixit opening tool to remove the pink panels.

First, remove the pink panels on each side of the handle in order to access the screws.

Use the iFixit opening tool to remove the pink panels.

1024

Step 2

• After removing the pink panels, there will be one visible screw on each side of the dryer handle measuring at 11mm.
• Carefully unscrew both of these screws with a tri-point Y000 screwdriver.
• Next, completely remove the screws out of the dryer handle.

After removing the pink panels, there will be one visible screw on each side of the dryer handle measuring at 11mm.

Carefully unscrew both of these screws with a tri-point Y000 screwdriver.

Next, completely remove the screws out of the dryer handle.

Step 3

• Remove the barrel by twisting and pulling it away from the handle of the dryer.
• Before attempting to take the barrel off, make sure the dryer powered completely off and is cool to the touch.

Remove the barrel by twisting and pulling it away from the handle of the dryer.

Before attempting to take the barrel off, make sure the dryer powered completely off and is cool to the touch.

Step 4

              Cord and Plug               

• Next, slide down the air inlet and the setting dial to reveal the 11mm screws on each side of the handle at the bottom of the hair dryer.

Next, slide down the air inlet and the setting dial to reveal the 11mm screws on each side of the handle at the bottom of the hair dryer.

Step 5

• There will be one visible screw on each side of the dryer at the bottom of the handle, measuring at 11mm.
• Carefully unscrew both of these screws with a tri-point Y000 screwdriver.
• Store screws in a safe place, you will need them to reassemble the device later.

There will be one visible screw on each side of the dryer at the bottom of the handle, measuring at 11mm.

Store screws in a safe place, you will need them to reassemble the device later.

Step 6

• Place the iFixit opening tool along the seams of the handle and pry the two pieces apart.

Place the iFixit opening tool along the seams of the handle and pry the two pieces apart.

Step 7

• Once you have exposed the inside of the dryer, you will see a clear port at the very end where the cord is connected and plugged into.
• Now, with your thumb and pointer finger gently pinch the top and bottom of the clear port.
• Next with your free hand carefully pull the cord out of the port of the dryer handle.

Once you have exposed the inside of the dryer, you will see a clear port at the very end where the cord is connected and plugged into.

Now, with your thumb and pointer finger gently pinch the top and bottom of the clear port.

Next with your free hand carefully pull the cord out of the port of the dryer handle.

Step 8

              Setting Dial               

• Once the cord is disconnected from the handle, you should be able to slide the dial setting off completely and free it from the cord.

Once the cord is disconnected from the handle, you should be able to slide the dial setting off completely and free it from the cord.

Step 9

              Lint Filter               

• Remove the air inlet by sliding it completely off of the wire.

Remove the air inlet by sliding it completely off of the wire.

Step 10

• Take the lint filter out from the air inlet by peeling it from the sides.

Take the lint filter out from the air inlet by peeling it from the sides.

Step 11

              Air Inlet               

• Once the lint filter is detached from the plastic filter protector, you can now replace it.

Once the lint filter is detached from the plastic filter protector, you can now replace it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 2 other contributors 

                    Rory Chappuis                     

Member since: 03/21/2022

345 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges                           

Team

                       University of Alabama, Team 1-4, Bedsole Spring 2022                        

                                                  Member of University of Alabama, Team 1-4, Bedsole Spring 2022 



                    UA-BEDSOLE-S22S1G4                     


                                            3 Members                     


                                            5 Guides authored