Ridgid Angle Grinder R10202 Wiring Assembly Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

Wiring Assembly
10 steps

Flags

BackRidgid Angle Grinder R10202
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Wiring Assembly

Take hold of the Side Assembly Handle [8] and unscrew to detach from the grinder.

Take hold of the Side Assembly Handle [8] and unscrew to detach from the grinder.

1024

Step 2

To get to the guard, unscrew and remove the Clamp Nut [34], Grinding Wheel (not pictured) [35], and Backing Flange [36].

To get to the guard, unscrew and remove the Clamp Nut [34], Grinding Wheel (not pictured) [35], and Backing Flange [36].

Step 3

To remove the Guard [38], press and hold the Guard Lever [39] and rotate the head to line up the two arrows inlayed within the metal as seen in the photograph provided.
Once the arrows line up lift the Guard [38] from the grinder.

To remove the Guard [38], press and hold the Guard Lever [39] and rotate the head to line up the two arrows inlayed within the metal as seen in the photograph provided.

Once the arrows line up lift the Guard [38] from the grinder.

Step 4

Use TORX T20 Screwdriver to unscrew and remove 5 M5 x 16 mm, TORX Screws [28].
Use TORX T20 Screwdriver to unscrew and remove 1 M5 x 28 mm, TORX Screw [1].
Use TORX T10 Screwdriver to unscrew and remove 1 M3 x 10 mm Screw [26].

Use TORX T20 Screwdriver to unscrew and remove 5 M5 x 16 mm, TORX Screws [28].

Use TORX T20 Screwdriver to unscrew and remove 1 M5 x 28 mm, TORX Screw [1].

Use TORX T10 Screwdriver to unscrew and remove 1 M3 x 10 mm Screw [26].

Step 5

You should now be able to separate each side of the Handle Assembly [27] as seen in the first photograph.
Remove the side that should easily separate from the other.
One side will remain as seen in the second picture as it is still screwed in.

You should now be able to separate each side of the Handle Assembly [27] as seen in the first photograph.

Remove the side that should easily separate from the other.

One side will remain as seen in the second picture as it is still screwed in.

Step 6

Use a Hex Screwdriver to unscrew and remove the 2 8-16 x 1/2 in. Screws [29].

Use a Hex Screwdriver to unscrew and remove the 2 8-16 x 1/2 in. Screws [29].

Step 7

The Cord Clamp [30] should be easily removed as seen separated from the Power Cord [32].

The Cord Clamp [30] should be easily removed as seen separated from the Power Cord [32].

Step 8

Use a screwdriver to unscrew and remove 1 M4 x 14 mm Screw [23].

Use a screwdriver to unscrew and remove 1 M4 x 14 mm Screw [23].

Step 9

The whole wiring assembly should be able to be lifted out of where it currently is as seen in the first photograph.
Allow the wiring assembly to hang from the grinder as seen in the second picture.
Press and hold the Handle Lock Button [24] to release the second side of the Handle Assembly [27].

The whole wiring assembly should be able to be lifted out of where it currently is as seen in the first photograph.

Allow the wiring assembly to hang from the grinder as seen in the second picture.

Press and hold the Handle Lock Button [24] to release the second side of the Handle Assembly [27].

Step 10

Use screwdriver to unscrew 4 M3.5 x 7 mm Screws [22].
The Switch [21], Power Cord [32], and Motor Housing [11] should now all be separated as seen in the third photograph.

Use screwdriver to unscrew 4 M3.5 x 7 mm Screws [22].

The Switch [21], Power Cord [32], and Motor Housing [11] should now all be separated as seen in the third photograph.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 3 other contributors

                    Parker Massie

Member since: 01/10/2019

607 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Oregon Institute of Technology, Team S1-G2, Lancaster Winter 2019                        

                                                  Member of Oregon Institute of Technology, Team S1-G2, Lancaster Winter 2019 



                    OIT-LANCASTER-W19S1G2                     


                                            4 Members                     


                                            6 Guides authored

Fahed - Aug 30, 2020

Be careful while jointing the wires because it can cause you some electric issues for more info you can read this guide.

Introduction#

What you need#

Team#

Introduction

What you need

Team