Difficulty

Easy

Steps

7

Time Required

                          5 - 15 minutes

Sections

1

  • Front Light
  • 7 steps

Flags

0

  • BackRidgid JobMax R2851 Series B

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

This repair requires minimal tools listed in the guide, and can be done in a short amount of time. Additionally you should remember to unplug your device before starting any repairs to avoid risk of being electrocuted.

What you need

Step 1

              Front Light
  • Unplug the device from the wall.
  • Orient the device so that the trigger is facing downwards.
  • Place your thumb and index finger on the two buttons located on the head of the tool.
  • Press the two buttons in and pull the head of the tool off.

Unplug the device from the wall.

Orient the device so that the trigger is facing downwards.

Place your thumb and index finger on the two buttons located on the head of the tool.

Press the two buttons in and pull the head of the tool off.

1024

Step 2

  • Loosen all eight 15mm T10 Torx screws.
  • You do not need to fully remove the screws yet; just loosen them enough that the device shell starts to open.

Loosen all eight 15mm T10 Torx screws.

You do not need to fully remove the screws yet; just loosen them enough that the device shell starts to open.

Step 3

  • Orient the device so that the cord end is facing upwards.
  • Take a small cutting tool, and cut down the seam in the back, ensuring that you only cut the sticker.
  • Make a shallow cut to avoid damaging internal hardware.

Orient the device so that the cord end is facing upwards.

Take a small cutting tool, and cut down the seam in the back, ensuring that you only cut the sticker.

Make a shallow cut to avoid damaging internal hardware.

Step 4

  • Completely remove all eight 15mm T10 Torx screws.

Completely remove all eight 15mm T10 Torx screws.

Step 5

  • Pull the device case off, gripping at the back of the case and rotating it towards the front of the device.
  • Once the device has been separated gently pull on the trigger assembly to remove it from one side of the case.
  • Watch out for the locking mechanism for the head of the device when removing.

Pull the device case off, gripping at the back of the case and rotating it towards the front of the device.

Once the device has been separated gently pull on the trigger assembly to remove it from one side of the case.

Watch out for the locking mechanism for the head of the device when removing.

Step 6

  • Once the device is apart, grab the LED light located in front of the trigger.
  • Slide the light upwards and out, freeing it from the device.

Once the device is apart, grab the LED light located in front of the trigger.

Slide the light upwards and out, freeing it from the device.

Step 7

  • Once the light is free snip the wires and replace.
  • A soldering iron will be needed when installing a new LED.

Once the light is free snip the wires and replace.

A soldering iron will be needed when installing a new LED.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Brent Shepherd

Member since: 02/12/2019

884 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Western Carolina University, Team S1-G5, Virtue Spring 2019                        

                                                  Member of Western Carolina University, Team S1-G5, Virtue Spring 2019 



                    WCU-VIRTUE-S19S1G5                     


                                            4 Members                     


                                            10 Guides authored