Ridgid R86034 Direction Switch Replacement Repair Guide

Difficulty

Very easy

Steps

Time Required

                          5 - 10 minutes

Sections

Disassembling Ridgid R86034 Housing
6 steps
Direction Switch
1 step

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackRidgid R86034
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Disassembling Ridgid R86034 Housing

Use the flat side of a metal spudger to peel the black rubber cover off of the casing.
Use some force; the rubber cover is securely attached to the housing.
Rotate the casing until it fits onto the housing with no gaps between it and the clear cover.
Orientation is important when putting the rubber cover on the casing.

Use the flat side of a metal spudger to peel the black rubber cover off of the casing.

Use some force; the rubber cover is securely attached to the housing.

Rotate the casing until it fits onto the housing with no gaps between it and the clear cover.

Orientation is important when putting the rubber cover on the casing.

1024

Step 2

Remove the plastic cover with your hands.
There is no need to force off the plastic cover. The plastic cover should be much easier to remove than the rubber cover.

Remove the plastic cover with your hands.

There is no need to force off the plastic cover. The plastic cover should be much easier to remove than the rubber cover.

Step 3

Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver.
Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove.

Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver.

Use a firm grip to peel off the back panel. It is sealed tight and requires a good amount of force to remove.

Step 4

Unscrew the eight 15 mm T10 Torx screws from the housing
The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead, use a conventional screwdriver that fits.

Unscrew the eight 15 mm T10 Torx screws from the housing

The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead, use a conventional screwdriver that fits.

Step 5

Place the driver flat on a table before completely separating the two halves of the housing so components of the drill don’t fall out during opening.
Pry apart the two halves of the housing at the back side of the driver using the metal spudger.
The housing is easier to remove if you pry from multiple sides.

Place the driver flat on a table before completely separating the two halves of the housing so components of the drill don’t fall out during opening.

Pry apart the two halves of the housing at the back side of the driver using the metal spudger.

The housing is easier to remove if you pry from multiple sides.

Step 6

Do not remove the direction switch.
Pull out all electrical components from housing by hand.
Lift out the motor.
Follow the wires.
The components should come out of their respective slots with ease and require little force to lift out.
The circuit board located nearest the battery pack and the LED light will be hard to pull out.
Remember to precisely place all components in their correct slots with their correct orientations when reassembling.

Do not remove the direction switch.

Pull out all electrical components from housing by hand.

Lift out the motor.

Follow the wires.

The components should come out of their respective slots with ease and require little force to lift out.

The circuit board located nearest the battery pack and the LED light will be hard to pull out.

Remember to precisely place all components in their correct slots with their correct orientations when reassembling.

Step 7

              Direction Switch

Remove the broken direction switch.
Replace the broken direction switch with a functional switch.
If the trigger is the part thats broken, you will need to replace the entire trigger assembly. Refer to our RIDGID X4 18V Lithium-Ion Impact Driver Trigger Assembly Replacement Guide

Remove the broken direction switch.

Replace the broken direction switch with a functional switch.

If the trigger is the part thats broken, you will need to replace the entire trigger assembly. Refer to our RIDGID X4 18V Lithium-Ion Impact Driver Trigger Assembly Replacement Guide

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 6 other contributors

                    Sean Liston

Member since: 04/28/2015

311 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 15-5, Amido Spring 2015                        

                                                  Member of Cal Poly, Team 15-5, Amido Spring 2015 



                    CPSU-AMIDO-S15S15G5                     


                                            4 Members                     


                                            12 Guides authored

Better Introduction#

Introduction#

What you need#

Team#

Better Introduction

Introduction

What you need

Team