Difficulty
Moderate
Steps
17
Time Required
35 - 55 minutes
Sections
4
- Battery
- 6 steps
- Camera
- 7 steps
- Microphone
- 3 steps
- Speakers
- 1 step
Flags
0
BackRing Stick Up Cam
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the six 6mm Phillips #00 screws from the back of the device.
Remove the six 6mm Phillips #00 screws from the back of the device.
1024
Step 2
- Pry off the aluminum plate using a plastic opening tool.
Pry off the aluminum plate using a plastic opening tool.
Step 3
- Remove the two 6mm Phillips #00 screws that were under the aluminum plate.
Remove the two 6mm Phillips #00 screws that were under the aluminum plate.
Step 4
- Pry off the back cover using a plastic opening tool.
Pry off the back cover using a plastic opening tool.
Step 5
- Disconnect the battery power leads using a plastic opening tool.
Disconnect the battery power leads using a plastic opening tool.
Step 6
- Use a plastic opening tool to loosen the adhesive holding the battery in place and remove the battery by hand.
Use a plastic opening tool to loosen the adhesive holding the battery in place and remove the battery by hand.
Step 7
Camera
- Remove the three silver 6mm Phillips #00 screws holding the motherboard in the device.
Remove the three silver 6mm Phillips #00 screws holding the motherboard in the device.
Step 8
- Disconnect the ribbon connector shown in the photo.
Disconnect the ribbon connector shown in the photo.
Step 9
- Remove the motherboard from the device by hand.
Remove the motherboard from the device by hand.
Step 10
- Remove the two black 5mm Phillips #00 screws holding the camera board into the device.
- Remove the single silver 10mm Phillips #00 screw holding the camera board into the device.
Remove the two black 5mm Phillips #00 screws holding the camera board into the device.
Remove the single silver 10mm Phillips #00 screw holding the camera board into the device.
Step 11
- Remove the three plastic spacers shown in the photo by hand.
Remove the three plastic spacers shown in the photo by hand.
Step 12
- Carefully disconnect the camera board from the daughterboard by sliding a plastic opening tool between the camera board and the daughterboard.
Carefully disconnect the camera board from the daughterboard by sliding a plastic opening tool between the camera board and the daughterboard.
Step 13
- Lift the camera board out of the housing using your hand.
Lift the camera board out of the housing using your hand.
Step 14
Microphone
- Remove the six silver 4.5mm Phillips #00 screws holding the daughterboard into the device.
Remove the six silver 4.5mm Phillips #00 screws holding the daughterboard into the device.
Step 15
- Use a plastic opening tool to carefully pry the microphone from the housing.
Use a plastic opening tool to carefully pry the microphone from the housing.
Step 16
- Use your hands to remove the daughterboard containing the microphone from the housing.
Use your hands to remove the daughterboard containing the microphone from the housing.
Step 17
Speakers
- Using a plastic opening tool, remove both of the speakers.
Using a plastic opening tool, remove both of the speakers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Chunyue Liu
Member since: 02/06/2019
273 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
UC Davis, Team S18-G3, Lore Winter 2019
Member of UC Davis, Team S18-G3, Lore Winter 2019
UCD-LORE-W19S18G3
3 Members
8 Guides authored
