Difficulty
Moderate
Steps
12
Time Required
15 minutes
Sections
3
- Base Plate
- 2 steps
- Power Button
- 3 steps
- Heating Element
- 7 steps
Flags
2
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
BackRival CM4015
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Base Plate
- Remove the three 16 mm tri-point screws from the base plate.
Remove the three 16 mm tri-point screws from the base plate.
1024
Step 2
- Remove the base plate by pressing the plastic body away from the metal plate with your thumbs.
Remove the base plate by pressing the plastic body away from the metal plate with your thumbs.
Step 3
Power Button
- Remove the 8mm Phillips screw that attaches the power button to the inside of the coffee maker.
Remove the 8mm Phillips screw that attaches the power button to the inside of the coffee maker.
Step 4
- Use a flat head screwdriver to pry the power button from its slot in the body of the device.
- Make sure the tool is pressed securely under the plastic clip, in order to not break it.
Use a flat head screwdriver to pry the power button from its slot in the body of the device.
Make sure the tool is pressed securely under the plastic clip, in order to not break it.
Step 5
- Clean both the button and its slot before replacing the power button.
Clean both the button and its slot before replacing the power button.
Step 6
Heating Element
- Remove the two 8 mm Phillips screws from the plastic body.
Remove the two 8 mm Phillips screws from the plastic body.
Step 7
- Remove the two 8 mm Phillips screws from the chassis of coffee maker.
- Pull back the metal backing from the plastic body.
Remove the two 8 mm Phillips screws from the chassis of coffee maker.
Pull back the metal backing from the plastic body.
Step 8
- Remove the four 8 mm Phillips screws from the inner plastic body.
- You will need a long, thin Phillips screw driver to get this deep into the device.
Remove the four 8 mm Phillips screws from the inner plastic body.
You will need a long, thin Phillips screw driver to get this deep into the device.
Step 9
- Flip the device upside down and remove the outer plastic body from the device by pulling straight up.
- Take your time to make sure the thin cables within the device don’t tear.
Flip the device upside down and remove the outer plastic body from the device by pulling straight up.
Take your time to make sure the thin cables within the device don’t tear.
Step 10
- Remove the two 8 mm Phillips screws from the metal backing.
Remove the two 8 mm Phillips screws from the metal backing.
Step 11
- Remove the 4 springs holding the water tubes by squeezing the 2 prongs together.
- You may also use pliers for this step if the springs are too strong.
Remove the 4 springs holding the water tubes by squeezing the 2 prongs together.
You may also use pliers for this step if the springs are too strong.
Step 12
- Bend the heating element back and forth to wiggle the water tubes loose from the plastic.
Bend the heating element back and forth to wiggle the water tubes loose from the plastic.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Michael Murdock
Member since: 10/06/2016
261 Reputation
2 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 10-6, Livingston Fall 2016
Member of Cal Poly, Team 10-6, Livingston Fall 2016
CPSU-LIVINGSTON-F16S10G6
5 Members
6 Guides authored
