Rival Mini Chopper Mc 67Bl Power Button Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Turning Gears
8 steps
Power Button
6 steps

Flags

BackRival Mini Chopper MC-67BL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Turning Gears

Twist the plastic lid counterclockwise to unlock it.
Lift the lid to remove it from the container.

Twist the plastic lid counterclockwise to unlock it.

Lift the lid to remove it from the container.

1024

Step 2

Carefully remove the blade from the container.
For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

Carefully remove the blade from the container.

For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

Step 3

With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

Step 4

Use your fingers to pry out the two rubber feet from the bottom cover of the base.
The two feet furthest from the button tower contain screws. The other two feet do not.

Use your fingers to pry out the two rubber feet from the bottom cover of the base.

The two feet furthest from the button tower contain screws. The other two feet do not.

Step 5

Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.
Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

Step 6

Firmly lift the bottom cover off of the base.

Firmly lift the bottom cover off of the base.

Step 7

Remove the smaller white gear by lifting it up with your hand.

Remove the smaller white gear by lifting it up with your hand.

Step 8

Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.
Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.
Continue turning the gear until completely removed from the blade-shaft.

Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

Continue turning the gear until completely removed from the blade-shaft.

Step 9

              Power Button

Use your hand to firmly pull the blade-shaft from the base.

Use your hand to firmly pull the blade-shaft from the base.

Step 10

Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

Step 11

Unwind power cord from the base pegs.

Unwind power cord from the base pegs.

Step 12

Use the plastic opening tool to pry open the base from the main body.
These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.
Once freed, lift the base panel from the main body and set it aside.

Use the plastic opening tool to pry open the base from the main body.

These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

Once freed, lift the base panel from the main body and set it aside.

Step 13

Use a Phillips #2 screwdriver to remove the three 9.53-mm screws from inside the main body.
Next, turn the device upright and lift the upper casing from around the button gently.

Use a Phillips #2 screwdriver to remove the three 9.53-mm screws from inside the main body.

Next, turn the device upright and lift the upper casing from around the button gently.

Step 14

Remove the button by simply pulling it up.
Don’t lose the spring under the button! Without it, the blender will not function.

Remove the button by simply pulling it up.

Don’t lose the spring under the button! Without it, the blender will not function.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors

                    David Otsu

Member since: 10/16/2013

109 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team 4-29, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 4-29, Amido Fall 2013 



                    CPSU-AMIDO-F13S4G29                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team