Rival Mini Chopper Mc 67Bl Power Cord Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          30 minutes

Sections

Turning Gears
8 steps
Power Cord
8 steps

Flags

BackRival Mini Chopper MC-67BL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Turning Gears

Twist the plastic lid counterclockwise to unlock it.
Lift the lid to remove it from the container.

Twist the plastic lid counterclockwise to unlock it.

Lift the lid to remove it from the container.

1024

Step 2

Carefully remove the blade from the container.
For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

Carefully remove the blade from the container.

For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

Step 3

With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

Step 4

Use your fingers to pry out the two rubber feet from the bottom cover of the base.
The two feet furthest from the button tower contain screws. The other two feet do not.

Use your fingers to pry out the two rubber feet from the bottom cover of the base.

The two feet furthest from the button tower contain screws. The other two feet do not.

Step 5

Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.
Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

Step 6

Firmly lift the bottom cover off of the base.

Firmly lift the bottom cover off of the base.

Step 7

Remove the smaller white gear by lifting it up with your hand.

Remove the smaller white gear by lifting it up with your hand.

Step 8

Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.
Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.
Continue turning the gear until completely removed from the blade-shaft.

Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

Continue turning the gear until completely removed from the blade-shaft.

Step 9

              Power Cord

Use your hand to firmly pull the blade-shaft from the base.

Use your hand to firmly pull the blade-shaft from the base.

Step 10

Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

Step 11

Unwind power cord from the base pegs.

Unwind power cord from the base pegs.

Step 12

Use the plastic opening tool to pry open the base from the main body.
These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.
Once freed, lift the base panel from the main body. The motor and power cable are connected to this panel.

Use the plastic opening tool to pry open the base from the main body.

These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

Once freed, lift the base panel from the main body. The motor and power cable are connected to this panel.

Step 13

Pull the power cord wires up from underneath the wire hook on the side of the motor.

Pull the power cord wires up from underneath the wire hook on the side of the motor.

Step 14

Carefully cut into black wire casing for both wires using a small knife and peel away the black casing.
Only cut deep enough to remove the casing.
For reassembly you will need black electrical tape to keep the wires from being exposed.

Carefully cut into black wire casing for both wires using a small knife and peel away the black casing.

Only cut deep enough to remove the casing.

For reassembly you will need black electrical tape to keep the wires from being exposed.

Step 15

Using a soldering kit, remove the solder for the black power cord from the circuit board.
Follow this soldering guide if you need extra help!

Using a soldering kit, remove the solder for the black power cord from the circuit board.

Follow this soldering guide if you need extra help!

Step 16

Use a small knife to cut the copper wires from the bracket holding the black wire and power cord together.
For reassembly the copper wires will need to be soldered together.

Use a small knife to cut the copper wires from the bracket holding the black wire and power cord together.

For reassembly the copper wires will need to be soldered together.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Roxanne

Member since: 10/17/2013

522 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 4-29, Amido Fall 2013                        

                                                  Member of Cal Poly, Team 4-29, Amido Fall 2013 



                    CPSU-AMIDO-F13S4G29                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team