Difficulty

Moderate

Steps

9

Time Required

                          10 - 15 minutes

Sections

3

  • Saw Casing
  • 5 steps
  • Motor
  • 2 steps
  • Safety Lock Pin
  • 2 steps

Flags

0

  • BackRotoZip Rebel REB01 Type 2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Saw Casing
  • Unplug the saw before attempting any of the replacement guides.
  • Orient the saw so that the handle is closest to you and the saw end points towards the left.

Unplug the saw before attempting any of the replacement guides.

Orient the saw so that the handle is closest to you and the saw end points towards the left.

1024

Step 2

  • Push down on the grey lock on the right side of the handle to unlock it.
  • Pull the handle to detach it from the saw.

Push down on the grey lock on the right side of the handle to unlock it.

Pull the handle to detach it from the saw.

Step 3

  • Lift the black lock at the tip of the saw to unlock the depth gauge.
  • Pull the depth gauge to detach it from the saw.

Lift the black lock at the tip of the saw to unlock the depth gauge.

Pull the depth gauge to detach it from the saw.

Step 4

  • Rotate the device so that the bottom of the saw is facing upwards.
  • Remove the six 20mm screws with a 6mm flathead screwdriver.

Rotate the device so that the bottom of the saw is facing upwards.

Remove the six 20mm screws with a 6mm flathead screwdriver.

Step 5

  • Cut through the stickers on the right and left sides of the saw using a metal spudger.
  • Pull off the top half of the casing.

Cut through the stickers on the right and left sides of the saw using a metal spudger.

Pull off the top half of the casing.

Step 6

              Motor
  • Lift the motor assembly out of the casing.
  • The white plastic piece connecting the wires and holding the motor brushes in place is fragile. Be careful to not break it when removing the motor assembly.

Lift the motor assembly out of the casing.

The white plastic piece connecting the wires and holding the motor brushes in place is fragile. Be careful to not break it when removing the motor assembly.

Step 7

  • Detach the wire connected to the bottom of the motor assembly.
  • Rotate the motor away from you so that the second wire is visible, and detach that wire as well.

Detach the wire connected to the bottom of the motor assembly.

Rotate the motor away from you so that the second wire is visible, and detach that wire as well.

Step 8

              Safety Lock Pin
  • Remove the sliding washer holding the pin in place.
  • The sliding washer is not shown in this guide. The action shows where the washer should be located.

Remove the sliding washer holding the pin in place.

The sliding washer is not shown in this guide. The action shows where the washer should be located.

Step 9

  • Flip the saw so that the ‘Rotozip’ label is facing upwards.
  • Remove the safety lock pin and spring.

Flip the saw so that the ‘Rotozip’ label is facing upwards.

Remove the safety lock pin and spring.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Lauren Russell

Member since: 10/05/2016

212 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 4-4, Livingston Fall 2016                        

                                                  Member of Cal Poly, Team 4-4, Livingston Fall 2016 



                    CPSU-LIVINGSTON-F16S4G4                     


                                            4 Members                     


                                            5 Guides authored

Kennith Murray - Jan 4, 2019

Reply

Where can I find replacement parts for this Particular rotozip model #reb01 type 2