Difficulty

Moderate

Steps

10

Time Required

                          10 - 15 minutes

Sections

3

  • Saw Casing
  • 5 steps
  • Motor
  • 2 steps
  • Power Switch Circuit Board
  • 3 steps

Flags

0

  • BackRotoZip Rebel REB01 Type 2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Saw Casing
  • Unplug the saw before attempting any of the replacement guides.
  • Orient the saw so that the handle is closest to you and the saw end points towards the left.

Unplug the saw before attempting any of the replacement guides.

Orient the saw so that the handle is closest to you and the saw end points towards the left.

1024

Step 2

  • Push down on the grey lock on the right side of the handle to unlock it.
  • Pull the handle to detach it from the saw.

Push down on the grey lock on the right side of the handle to unlock it.

Pull the handle to detach it from the saw.

Step 3

  • Lift the black lock at the tip of the saw to unlock the depth gauge.
  • Pull the depth gauge to detach it from the saw.

Lift the black lock at the tip of the saw to unlock the depth gauge.

Pull the depth gauge to detach it from the saw.

Step 4

  • Rotate the device so that the bottom of the saw is facing upwards.
  • Remove the six 20mm screws with a 6mm flathead screwdriver.

Rotate the device so that the bottom of the saw is facing upwards.

Remove the six 20mm screws with a 6mm flathead screwdriver.

Step 5

  • Cut through the stickers on the right and left sides of the saw using a metal spudger.
  • Pull off the top half of the casing.

Cut through the stickers on the right and left sides of the saw using a metal spudger.

Pull off the top half of the casing.

Step 6

              Motor
  • Lift the motor assembly out of the casing.
  • The white plastic piece connecting the wires and holding the motor brushes in place is fragile. Be careful to not break it when removing the motor assembly.

Lift the motor assembly out of the casing.

The white plastic piece connecting the wires and holding the motor brushes in place is fragile. Be careful to not break it when removing the motor assembly.

Step 7

  • Detach the wire connected to the bottom of the motor assembly.
  • Rotate the motor away from you so that the second wire is visible, and detach that wire as well.

Detach the wire connected to the bottom of the motor assembly.

Rotate the motor away from you so that the second wire is visible, and detach that wire as well.

Step 8

              Power Switch Circuit Board
  • Slide the red bumper switch off the casing.
  • The power cord is not shown, but does not need to be removed.

Slide the red bumper switch off the casing.

The power cord is not shown, but does not need to be removed.

Step 9

  • Pinch the two white clips with your thumb while simultaneously pulling the black and white wires.
  • The motor assembly is shown in this picture, do not worry about it since you have removed it in the previous steps.

Pinch the two white clips with your thumb while simultaneously pulling the black and white wires.

The motor assembly is shown in this picture, do not worry about it since you have removed it in the previous steps.

Step 10

  • Pull the circuit board upward to remove it from the casing.

Pull the circuit board upward to remove it from the casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Lauren Russell

Member since: 10/05/2016

212 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 4-4, Livingston Fall 2016                        

                                                  Member of Cal Poly, Team 4-4, Livingston Fall 2016 



                    CPSU-LIVINGSTON-F16S4G4                     


                                            4 Members                     


                                            5 Guides authored

Andrew Doble - Apr 7, 2020

Reply

Nice guide, I can’t seem to find the switch online, it seems to be discontinued