Difficulty

Moderate

Steps

6

Time Required

                          20 minutes

Sections

1

  • Protective Shell
  • 6 steps

Flags

0

  • BackRyobi CSB125

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Protective Shell
  • Place the saw on a flat surface with the blade facing up.
  • Make sure that the saw is unplugged from any power source.

Place the saw on a flat surface with the blade facing up.

Make sure that the saw is unplugged from any power source.

1024

Step 2

  • Remove the bumper by using the T20 Torx screwdriver to loosen the M5 x 20mm screw.

Remove the bumper by using the T20 Torx screwdriver to loosen the M5 x 20mm screw.

Step 3

  • Use the 7”/32 allen key to loosen the 5/16-18 x 9/16 in. blade screw.

Use the 7”/32 allen key to loosen the 5/16-18 x 9/16 in. blade screw.

Step 4

  • Remove the 5/16-18 x 9/16 in. blade screw, spring washer, the outer blade washer, the blade, and the inner blade washer.

Remove the 5/16-18 x 9/16 in. blade screw, spring washer, the outer blade washer, the blade, and the inner blade washer.

Step 5

  • Use the Phillips #2 screwdriver to remove the four M4x16mm screws shown.
  • You will need to rotate the protective shell around in order to access them.

Use the Phillips #2 screwdriver to remove the four M4x16mm screws shown.

You will need to rotate the protective shell around in order to access them.

Step 6

  • Remove the lower blade guard support assembly from the rest of the saw.
  • Remove the protective shell.

Remove the lower blade guard support assembly from the rest of the saw.

Remove the protective shell.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.

Author

                                      with 1 other contributor 


                    Curtis Melo

Member since: 10/31/2019

1,039 Reputation

                                      5 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       UMass Dartmouth, Team S2-G1, Barthe Fall 2019                        

                                                  Member of UMass Dartmouth, Team S2-G1, Barthe Fall 2019 



                    UMASSD-BARTHE-F19S2G1                     


                                            3 Members                     


                                            5 Guides authored

Michael Bluejay - May 13, 2021

Reply

Instructions fail at step #5. Bottom-left screw is under the plastic blade guard which blocks removal of the screw. Blade guard covers the screw no matter how it’s positioned.

Adrian Isbister - Aug 1, 2021

If you wiggle the plastic you can remove

I was able to remove… be patient it does work

Instructions also fail at step #6. I have no idea how to remove the plastic blade guard from the axle so I can transfer it to the new (replacement) blade guard.

Adrian Isbister - Aug 1, 2021

Reply

I also was struggling… … but if you look closely there is a thin metal ring around the center plastic ring that the spindle runs through… this has a split in it…. I used a small flat Precision screwdriver (type used to tighten reading glasses,etc)and was able to pry at the split and remove the thin metal ring.

Once removed this frees the plastic guard and it drops right out.

Just reverse to reassemble.

This works… just be patient