Difficulty
Moderate
Steps
8
Time Required
15 minutes
Sections
2
- Battery and Handle
- 1 step
- Body
- 7 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackRYOBI P422
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery and Handle
- To remove the battery press down on the two buttons located on each side of the battery and pull away from the body of the grinder.
- To remove the handle hold grinder with one hand and use the other hand to unscrew the handle with a counter-clockwise motion
To remove the battery press down on the two buttons located on each side of the battery and pull away from the body of the grinder.
To remove the handle hold grinder with one hand and use the other hand to unscrew the handle with a counter-clockwise motion
1024
Step 2
Body
- Lay the grinder flat on its side so the screws are facing up.
Lay the grinder flat on its side so the screws are facing up.
Step 3
- Remove the four 1.8 cm screws from the lower and mid section of the body with the Torx T20 screwdriver.
- Remove the 3.7 cm screws from the upper section of the body, with the same screwdriver.
Remove the four 1.8 cm screws from the lower and mid section of the body with the Torx T20 screwdriver.
Remove the 3.7 cm screws from the upper section of the body, with the same screwdriver.
Step 4
- Now that the two halves are unscrewed, lift up the top half.
Now that the two halves are unscrewed, lift up the top half.
Step 5
- Remove the safety trigger and the spring.
- Be careful in removing the safety trigger, the pin may fall out as you are moving it.
Remove the safety trigger and the spring.
Be careful in removing the safety trigger, the pin may fall out as you are moving it.
Step 6
- Lift up main trigger and spring together.
- By lifting this trigger and spring out of the handle, you will pull double duty by lifting the black switch box off of its two support posts.
- Slide the trigger off of the black switch box.
- Be careful when removing trigger, the spring will be compressed and may move unexpectedly.
Lift up main trigger and spring together.
By lifting this trigger and spring out of the handle, you will pull double duty by lifting the black switch box off of its two support posts.
Slide the trigger off of the black switch box.
Be careful when removing trigger, the spring will be compressed and may move unexpectedly.
Step 7
- Lift the battery lead bracket from its slot.
- Use the PH 1 screwdriver to unscrew the two 0.7 cm screws that hold the 2.6 cm long brass bracket in place.
- Use tweezers to remove the brass bracket.
- During reassembly, remember to keep the spring inside the main trigger and against the bracket that is visible in the second of the accompanying photos.
Lift the battery lead bracket from its slot.
Use the PH 1 screwdriver to unscrew the two 0.7 cm screws that hold the 2.6 cm long brass bracket in place.
Use tweezers to remove the brass bracket.
During reassembly, remember to keep the spring inside the main trigger and against the bracket that is visible in the second of the accompanying photos.
Step 8
- Flip the grinder over and lift off the second half of the body.
- Now you can replace your damaged handles with a new pair.
Flip the grinder over and lift off the second half of the body.
Now you can replace your damaged handles with a new pair.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
John Lamanuzzi
Member since: 03/20/2015
217 Reputation
2 Guides authored
Badges:
8
+5 more badges
Team
UMass Dartmouth, Team 3-6, Duarte Spring 2015
Member of UMass Dartmouth, Team 3-6, Duarte Spring 2015
UMASSD-DUARTE-S15S3G6
3 Members
5 Guides authored
