Difficulty
Difficult
Steps
14
Time Required
Suggest a time??
Sections
3
- Saw Bar Assembly
- 7 steps
- Assembly Bar Bearing
- 3 steps
- Motor
- 4 steps
Flags
7
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Missed a Step
Oops! This guide is currently missing some important steps.
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Confusing Text
Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Missing Details
Some of this guide’s details are missing. Help users by adding tools, difficulty, or time.
BackRyobi RJ1861V
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Saw Bar Assembly
- Use a Torx T5 screwdriver to remove the single 8 mm screw securing the shoe.
Use a Torx T5 screwdriver to remove the single 8 mm screw securing the shoe.
1024
Step 2
- Remove the rubber sleeve.
- You may have to use some force as it has a tight fit.
Remove the rubber sleeve.
You may have to use some force as it has a tight fit.
Step 3
- Use a Torx T5 screwdriver to remove the six screws on the underside of the device.
Use a Torx T5 screwdriver to remove the six screws on the underside of the device.
Step 4
- Use a Torx T5 screwdriver to remove the four screws on the top.
- There are two screws on each side of the device.
Use a Torx T5 screwdriver to remove the four screws on the top.
There are two screws on each side of the device.
Step 5
- Remove the backside panel.
Remove the backside panel.
Step 6
- Unscrew the four T5 Torx screws that are holding the assembly bar in place.
Unscrew the four T5 Torx screws that are holding the assembly bar in place.
Step 7
- Lift the assembly bar up and out of the chassis.
Lift the assembly bar up and out of the chassis.
Step 8
Assembly Bar Bearing
- Begin with the top of the device facing up.
Begin with the top of the device facing up.
Step 9
- Insert needle nose pliers to remove the retaining pin at the top of the bearing.
Insert needle nose pliers to remove the retaining pin at the top of the bearing.
Step 10
- Once the retaining pin has been removed, pull off the damaged bearing and insert a new one.
Once the retaining pin has been removed, pull off the damaged bearing and insert a new one.
Step 11
Motor
- The motor is divided into two section which are the back and front.
- The arrows indicate where the two motor locations .
The motor is divided into two section which are the back and front.
The arrows indicate where the two motor locations .
Step 12
- Use a Torx T5 screwdriver to remove the four screws on the top of the motor.
Use a Torx T5 screwdriver to remove the four screws on the top of the motor.
Step 13
- Use a Torx T5 screwdriver to remove the two screws inside the motor housing.
Use a Torx T5 screwdriver to remove the two screws inside the motor housing.
Step 14
- Remove the four screws on the back of the motor with a Torx T5 screwdriver.
- Pull the motor directly out of the housing.
Remove the four screws on the back of the motor with a Torx T5 screwdriver.
Pull the motor directly out of the housing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Adrian Williams
Member since: 04/08/2019
183 Reputation
1 Guide authored
Badges:
3
Team
Eastern Washington University, Team S1-G1, Rowley Spring 2019
Member of Eastern Washington University, Team S1-G1, Rowley Spring 2019
EWU-ROWLEY-S19S1G1
3 Members
3 Guides authored
