Saeco Intelia Hd8752 Lcd Display Panel Replacement Repair Guide

Difficulty

Moderate

Steps

9

Time Required

                          45 minutes            

Sections

1

• LCD Display Panel
• 9 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

• BackSaeco Intelia HD8752

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Disconnecting power               

• First, start by putting appliance into standby mode. Then put general switch to 0. Finally, disconnect power cord.

First, start by putting appliance into standby mode. Then put general switch to 0. Finally, disconnect power cord.

1024

Step 2

              Removing the bean coffee container and the upper casing cover               

• Start by removing all coffee beens from the container.
• Remove the screw in the middle of the bean container protection and remove the bean container protection.
• Remove the three screws of the been container and remove the been container.
• Use a magnet to get them up so that you don’t drop them into the grinder hole.
• You can now remove the upper casing cover by pulling it up gently (picture 2).

Start by removing all coffee beens from the container.

Remove the screw in the middle of the bean container protection and remove the bean container protection.

Remove the three screws of the been container and remove the been container.

Use a magnet to get them up so that you don’t drop them into the grinder hole.

You can now remove the upper casing cover by pulling it up gently (picture 2).

Step 3

              Removing left side casing               

• Remove the two screws on the top of the left panel.
• Remove the drip tray.
• Remove the water tank.
• Below the water tank location, remove the bottom screw of the left side casing.
• Remove the left side casing by pulling it gently. Take care of the nick, at the middle of the panel (above the yellow marked screw).

Remove the two screws on the top of the left panel.

Remove the drip tray.

Remove the water tank.

Below the water tank location, remove the bottom screw of the left side casing.

Remove the left side casing by pulling it gently. Take care of the nick, at the middle of the panel (above the yellow marked screw).

Step 4

              Removing silver front panel               

If Pannarello is present, remove it first from hot water dispenser by pulling it firmly to the bottom. Next, open up service gate on the right of the appliance.

Remove the two right screws of the silver front panel.

Remove the two left screws of the silver front panel.

Separate the silver front panel from the main unit by pulling it gently.

Be careful, you can’t remove silver front panel without removing first the hot water dispenser !

Loosen or remove the two screws of the hot water dispenser.

Remove the silver front panel. Take care of hot water dispenser and left and right nicks of the panel.

Step 5

              Removing the touch panel frame               

• Remove the three screws of the touch panel frame.

Remove the three screws of the touch panel frame.

Step 6

              Removing the LCD frame               

• Remove the LCD black plastic frame. It is simply placed into two necks.

Remove the LCD black plastic frame. It is simply placed into two necks.

Step 7

              Removing LCD screen               

• Remove the two screws on each side of the LCD screen.
• Disconnect the first connector.
• Disconnect the other cable.
• To disconnect the second cable, you need to lifts the flap of the connector.

Remove the two screws on each side of the LCD screen.

Disconnect the first connector.

Disconnect the other cable.

To disconnect the second cable, you need to lifts the flap of the connector.

Step 8

              Install the new LCD screen               

• Disassemble the old LCD screen from support frame.
• Clip the new LCD screen to the LCD support frame.
• Reconnect the two cables.

Disassemble the old LCD screen from support frame.

Clip the new LCD screen to the LCD support frame.

Reconnect the two cables.

Step 9

              You've done it !               

• Reconnect power cable and switch on the appliance. Colors (yellow, green) from the screen should be back :)
• If it doesn’t work, check connection after turning off the power.
• To reassemble the appliance, follow this guide in reverse order.

Reconnect power cable and switch on the appliance. Colors (yellow, green) from the screen should be back :)

If it doesn’t work, check connection after turning off the power.

To reassemble the appliance, follow this guide in reverse order.

To reassemble your appliance, follow the instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      16 other people completed this guide.                                             

Author

                                      with 1 other contributor 

                    Jean T                     

Member since: 02/19/2016

561 Reputation

                                      1 Guide authored                  



                       Badges:
                       12







                                                        +9 more badges                           

Schwarzstein - May 28, 2016

Reply

Great ! :) Thank you.

Jean T - Jul 1, 2016

You’re welcome :)

Paul Tast - Sep 17, 2016

Reply

Jean T - Jan 15, 2017

Hi Paul,

Rainer Bokowski - Nov 2, 2016

Reply

Very good Description! Trank you!!!