Difficulty

Moderate

Steps

6

Time Required

Suggest a time??

Sections

1

  • Brewing unit gasket
  • 6 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSaeco Minuto

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Brewing unit gasket
  • Open the hatch on the side panel and remove the brewing unit.

Open the hatch on the side panel and remove the brewing unit.

1024

Step 2

  • The spout for the hot coffee is located on the top of the brewing unit. It is fastened with two screws. Underneath is the crema valve. It consists of a spring and a little glass ball. Make sure the spring is reinserted with the thin end touching the glass ball when re-assembling.
  • Remove the two Torx T10 screws on the crema valve.
  • Lift off the crema valve minding the spring and the glass ball.

The spout for the hot coffee is located on the top of the brewing unit. It is fastened with two screws. Underneath is the crema valve. It consists of a spring and a little glass ball. Make sure the spring is reinserted with the thin end touching the glass ball when re-assembling.

Remove the two Torx T10 screws on the crema valve.

Lift off the crema valve minding the spring and the glass ball.

Step 3

  • The upper piston is held in place in the frame with four locking pawls. Push down all four latches with a spudger, then remove the piston by pushing it downward.
  • If you want to replace the gasket, you can do this now and re-assemble the device and stop here. However, a general maintenance of the brewing unit is strongly recommended.
  • Unscrew the Torx T10 screw on the brewing sieve and remove it.

The upper piston is held in place in the frame with four locking pawls. Push down all four latches with a spudger, then remove the piston by pushing it downward.

If you want to replace the gasket, you can do this now and re-assemble the device and stop here. However, a general maintenance of the brewing unit is strongly recommended.

Unscrew the Torx T10 screw on the brewing sieve and remove it.

Step 4

  • There are three Torx T10 screws in deep blind holes that hold together the two parts of the brewing unit. Unscrew them and lift off the upper side panel.

There are three Torx T10 screws in deep blind holes that hold together the two parts of the brewing unit. Unscrew them and lift off the upper side panel.

Step 5

  • Now you can disassemble the brewing unit into its three main parts: the brewing unit and the two side panels.

Now you can disassemble the brewing unit into its three main parts: the brewing unit and the two side panels.

Step 6

  • You can push out the lower piston from the brewing unit if you snap the deflection lever out of its socket with a screw driver.
  • Clean all parts with very hot water and dishwasher liquid.
  • Grease all moving parts with food grade silicone fat. Dont forget the tracks in the side panels.

You can push out the lower piston from the brewing unit if you snap the deflection lever out of its socket with a screw driver.

Clean all parts with very hot water and dishwasher liquid.

Grease all moving parts with food grade silicone fat. Dont forget the tracks in the side panels.

Follow the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

Annika Faelker

jana°

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges