Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

1

  • Saeco brewing unit disassembly
  • 8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSaeco Royal

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Cream valve and spout
  • These parts differ in details depending on the model
  • Two screws hold the part, loosen. A seal becomes free, pick up well, better still replace later.
  • Inside is a feather and a small glass ball. Store carefully.

These parts differ in details depending on the model

Two screws hold the part, loosen. A seal becomes free, pick up well, better still replace later.

Inside is a feather and a small glass ball. Store carefully.

1024

Step 2

              The brewing sieve
  • With a 6mm Allen key (or the key that comes with the machine), the brewing sieve can be unscrewed. It strongly determines the aroma, if it is dirty the coffee tastes bad.

With a 6mm Allen key (or the key that comes with the machine), the brewing sieve can be unscrewed. It strongly determines the aroma, if it is dirty the coffee tastes bad.

Step 3

              The upper piston
  • He is held in place by four latches. These impress, e.g. with a screwdriver, then the piston can be pushed down.
  • The new sealing ring is already waiting, but first it has to be cleaned properly.

He is held in place by four latches. These impress, e.g. with a screwdriver, then the piston can be pushed down.

The new sealing ring is already waiting, but first it has to be cleaned properly.

Step 4

              Intake
  • Through the hole on the opposite side of the fixing screw can be solved. The inlet is plugged in and held by a latch, which you have to push away.

Through the hole on the opposite side of the fixing screw can be solved. The inlet is plugged in and held by a latch, which you have to push away.

Step 5

              dismantle
  • Three screws hold the brew groups together, loosen.
  • The whole mechanics can now be broken down into three big parts. The coffee funnel can stay.

Three screws hold the brew groups together, loosen.

The whole mechanics can now be broken down into three big parts. The coffee funnel can stay.

Step 6

              Umlenkhebel
  • That’s the trickiest part: you have to lever this lever out of its camp. To do this you drive with a screwdriver between the lever and the carrier and press it really very strong outwards. Now he grabs out - hopefully!

That’s the trickiest part: you have to lever this lever out of its camp. To do this you drive with a screwdriver between the lever and the carrier and press it really very strong outwards. Now he grabs out - hopefully!

Step 7

              Lower piston
  • Since the lever is gone you can easily pull out the piston. It has no seal.
  • The lower piston itself has no gasket. But the shaft of the piston slides in an o-ring. which is situated under the brewing chamber. It can be changed, but it´s not easy to do this.

Since the lever is gone you can easily pull out the piston. It has no seal.

The lower piston itself has no gasket. But the shaft of the piston slides in an o-ring. which is situated under the brewing chamber. It can be changed, but it´s not easy to do this.

Step 8

              Clean
  • That’s why we did it. All parts are thoroughly cleaned. For this purpose, a solution of machine detergent is good. (Use rubber gloves!) Clean all channels with pipe cleaners. The brewing sieve is like new again! Allow to dry well.
  • Then apply new gaskets, in particular to the crema valve and piston and lubricate with food-grade grease.
  • Fat also belongs to the bearings of the rocker arm and into the slides, the piston skirt, as well as into the water inlet

That’s why we did it. All parts are thoroughly cleaned. For this purpose, a solution of machine detergent is good. (Use rubber gloves!) Clean all channels with pipe cleaners. The brewing sieve is like new again! Allow to dry well.

Then apply new gaskets, in particular to the crema valve and piston and lubricate with food-grade grease.

Fat also belongs to the bearings of the rocker arm and into the slides, the piston skirt, as well as into the water inlet

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

        VauWeh is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges