Difficulty

Moderate

Steps

17

Time Required

Suggest a time??

Sections

2

  • Saeco Royal Opening Procedure
  • 5 steps
  • Remove thermoblock
  • 12 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSaeco Royal

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Preparing
  • Unplug!
  • Remove all attachments like water tank, brewing unit etc.
  • The pictures show a Royal Cappucino One Touch HD8930, but the opening procedure is similar to all models.

Unplug!

Remove all attachments like water tank, brewing unit etc.

The pictures show a Royal Cappucino One Touch HD8930, but the opening procedure is similar to all models.

1024

Step 2

              Top
  • The coffeebean supply is fixed with two screws. Unscrew them and lift it off.
  • There is a black rubber lid under the bean hopper that you can easily lift off, leaving a large opening.
  • The adjuster of the grinder has to be solved. Mark the position or just take a picture. This type is fixed with a screw, others are only sticked together.

The coffeebean supply is fixed with two screws. Unscrew them and lift it off.

There is a black rubber lid under the bean hopper that you can easily lift off, leaving a large opening.

The adjuster of the grinder has to be solved. Mark the position or just take a picture. This type is fixed with a screw, others are only sticked together.

Step 3

              Rear side
  • There are two screws to be turned out.

There are two screws to be turned out.

Step 4

              Front
  • The screws are situated on the underneath of the cover. This type is held by four screws.

The screws are situated on the underneath of the cover. This type is held by four screws.

Step 5

              Lift cover off
  • Now the cover can be raised: first grip on left and right rear side and lift about 10 cm (4 in). Sometimes the cover jams a little bit.
  • Solve the hoses which lead to the water tank. Perhaps you have to pull out some contacts, (e.g. the yellow-green protection lead), don´t forget to put them on again later.
  • The cover can be drawn aslant towards the front, sliding it over the hot water pipe.
  • Most repairs can be done with the cover being laid up partially , it must not be completely removed.

Now the cover can be raised: first grip on left and right rear side and lift about 10 cm (4 in). Sometimes the cover jams a little bit.

Solve the hoses which lead to the water tank. Perhaps you have to pull out some contacts, (e.g. the yellow-green protection lead), don´t forget to put them on again later.

The cover can be drawn aslant towards the front, sliding it over the hot water pipe.

Most repairs can be done with the cover being laid up partially , it must not be completely removed.

Step 6

              Remove thermoblock
  • This is what the removed thermoblock looks like. This one was 14 years old and leaking in various places.

This is what the removed thermoblock looks like. This one was 14 years old and leaking in various places.

Step 7

  • A look into the open device. The thermoblock is hidden under a pile of cables and tubes.

A look into the open device. The thermoblock is hidden under a pile of cables and tubes.

Step 8

  • It’s safer to number the cable connectors on the electronics. You probably just need to disconnect the slightly hidden # 14 connector on the two green cables at the very bottom and # 7 on the blue cable on the top.

It’s safer to number the cable connectors on the electronics. You probably just need to disconnect the slightly hidden # 14 connector on the two green cables at the very bottom and # 7 on the blue cable on the top.

Step 9

  • The thermoblock is attached to the wall behind the brew group with only two Phillips screws.
  • Remove the two Phillips screws circled in red.

The thermoblock is attached to the wall behind the brew group with only two Phillips screws.

Remove the two Phillips screws circled in red.

Step 10

  • Take out the thermoblock and place it on the machine.
  • Hold on! The thermoblock is still connected to the machine by many cables and hoses. Don’t attempt to completely remove it just yet!

Take out the thermoblock and place it on the machine.

Hold on! The thermoblock is still connected to the machine by many cables and hoses. Don’t attempt to completely remove it just yet!

Step 11

  • Pull the clamp on the hose to the steam valve off.
  • Pull the hose circled in orange out.
  • There are two seals at the end of the hose that stick to the hose. Exchange them during re-assembly.

Pull the clamp on the hose to the steam valve off.

Pull the hose circled in orange out.

There are two seals at the end of the hose that stick to the hose. Exchange them during re-assembly.

Step 12

  • Remove the metal holder of the thermal fuse.
  • My thermal fuse holder is heavily rusted, this may or may not be the case for you.

Remove the metal holder of the thermal fuse.

My thermal fuse holder is heavily rusted, this may or may not be the case for you.

Step 13

  • Pull first the clamp, and then the second pressure hose out of the thermoblock.
  • There are two seals at the end of the hose. They stay stuck either at the end of the hose or afterwards, so don’t try to remove them. Exchange them during re-assembly.

Pull first the clamp, and then the second pressure hose out of the thermoblock.

There are two seals at the end of the hose. They stay stuck either at the end of the hose or afterwards, so don’t try to remove them. Exchange them during re-assembly.

Step 14

  • Disconnect the connector with the two gray cables from the thermal switch.

Disconnect the connector with the two gray cables from the thermal switch.

Step 15

  • The blue cable from the thermoblock leads to the connector on the electronics, which is marked with 7 here. This particular plug stuck a lot, so force was required to pull it out.

The blue cable from the thermoblock leads to the connector on the electronics, which is marked with 7 here. This particular plug stuck a lot, so force was required to pull it out.

Step 16

  • The Allen screw, which holds the holder of the two thermocouples, was not easy to open…
  • This can also be a Phillips screw. It may vary which appears for you.
  • Therefore, the plug on the electronics with the two green cables was pulled out. The plug has the mark 14 and is at the very bottom of the electronics.
  • Disconnect the plug with the yellow-green grounding wire from the support valve.

The Allen screw, which holds the holder of the two thermocouples, was not easy to open…

This can also be a Phillips screw. It may vary which appears for you.

Therefore, the plug on the electronics with the two green cables was pulled out. The plug has the mark 14 and is at the very bottom of the electronics.

Disconnect the plug with the yellow-green grounding wire from the support valve.

Step 17

  • Thread the green and blue cables out.
  • The thermoblock is free. Lift it out of the machine.
  • To replace the thermoblock, the attached components must be removed from the old block and transferred to the new part.

Thread the green and blue cables out.

The thermoblock is free. Lift it out of the machine.

To replace the thermoblock, the attached components must be removed from the old block and transferred to the new part.

Repeat the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

[deleted]

George Youssef

Annika Faelker

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges