Difficulty

Moderate

Steps

8

Time Required

Suggest a time??

Sections

2

  • Removing Saeco Vienna Sup 018 Top Cover
  • 4 steps
  • Steam Valve
  • 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackSaeco Vienna Sup 018

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Removing Saeco Vienna Sup 018 Top Cover
  • Never forget: Pull the plug out!
  • Remove all attachments such as drawers, water tank, brewing unit.
  • Carefully pull the steam button out. If it is too tight, first loosen the cover (steps 2 to 4), lift slightly and then push the ratchet nose with a small screwdriver.

Never forget: Pull the plug out!

Remove all attachments such as drawers, water tank, brewing unit.

Carefully pull the steam button out. If it is too tight, first loosen the cover (steps 2 to 4), lift slightly and then push the ratchet nose with a small screwdriver.

1024

Step 2

  • The bean container is fixed with two Phillipps screws. Unscrew those.
  • The adjusters of the grinder and the quantity of coffee (if present) can remain.
  • Lift the bean container up und remove it from the device.

The bean container is fixed with two Phillipps screws. Unscrew those.

The adjusters of the grinder and the quantity of coffee (if present) can remain.

Lift the bean container up und remove it from the device.

Step 3

  • Remove the single T10 Torx screw on the rear edge of the top cover under the water reservoir.
  • Remove the single Phillipps screw on the rear edge of the top cover under the container of the coffee beans.
  • There are two Phillipps screws on the frontal unterside edge of the top cover. Turn them out.

Remove the single T10 Torx screw on the rear edge of the top cover under the water reservoir.

Remove the single Phillipps screw on the rear edge of the top cover under the container of the coffee beans.

There are two Phillipps screws on the frontal unterside edge of the top cover. Turn them out.

Step 4

  • Now the cover can be lifted off. Pull backwards, then diagonally forward. Remove the silicone hose from the water tank.

Now the cover can be lifted off. Pull backwards, then diagonally forward. Remove the silicone hose from the water tank.

Step 5

              Steam Valve
  • The steam valve is located on the top right of the machine. If it has cracks, water will drip out of the valve body.

The steam valve is located on the top right of the machine. If it has cracks, water will drip out of the valve body.

Step 6

  • Remove the clamp securing the pressure hose to the valve body.
  • Disconnect the pressure hose from the valve body.
  • The end of the pressure hose is sealed with two O-rings. Those will either stick on the valve body or on the pressure hose. Whenever possible replace them when re-assembling.

Remove the clamp securing the pressure hose to the valve body.

Disconnect the pressure hose from the valve body.

The end of the pressure hose is sealed with two O-rings. Those will either stick on the valve body or on the pressure hose. Whenever possible replace them when re-assembling.

Step 7

  • The steam valve must be pushed to the right, but a microswitch will still be in the way.
  • The microswitch is mounted on the underside of the gray frame with two notches. Insert a small screwdriver into the gap under the gray frame. Gently push the two notches one after the other and lift the microswitch upwards. The cables can stay connected.

The steam valve must be pushed to the right, but a microswitch will still be in the way.

The microswitch is mounted on the underside of the gray frame with two notches. Insert a small screwdriver into the gap under the gray frame. Gently push the two notches one after the other and lift the microswitch upwards. The cables can stay connected.

Step 8

  • The steam valve is still secured with a catch. Lift the catch with a flat-head screwdriver and slide the complete valve to the right.
  • To remove the valve it can now be pulled out of the gray frame in a forward direction.

The steam valve is still secured with a catch. Lift the catch with a flat-head screwdriver and slide the complete valve to the right.

To remove the valve it can now be pulled out of the gray frame in a forward direction.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

oldturkey03

VauWeh

Author

                                      with 1 other contributor 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges