Difficulty
Moderate
Steps
13
Time Required
10 - 15 minutes
Sections
3
- Battery
- 3 steps
- Casing
- 8 steps
- Back Speakers
- 2 steps
Flags
0
BackSamsung Ace
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- To remove the back casing, firmly press down and push towards the bottom of the phone.
To remove the back casing, firmly press down and push towards the bottom of the phone.
1024
Step 2
- With the casing removed, lift the battery from the indicated indentation.
With the casing removed, lift the battery from the indicated indentation.
Step 3
- From here, you can now access the SIM card and model/serial numbers.
From here, you can now access the SIM card and model/serial numbers.
Step 4
Casing
- Using the Phillips #00 screwdriver, remove the four indicated screws (4.5 mm).
Using the Phillips #00 screwdriver, remove the four indicated screws (4.5 mm).
Step 5
- Press the pointed edge of the spudger into the side of the two rubber plugs in order to lift and remove them from the top of the phone.
- Then, using the Phillips #00 screwdriver, remove the two indicated Phillip screws (6.5 mm).
Press the pointed edge of the spudger into the side of the two rubber plugs in order to lift and remove them from the top of the phone.
Then, using the Phillips #00 screwdriver, remove the two indicated Phillip screws (6.5 mm).
Step 6
- To remove the SIM card, start by pressing the top of the card and push down and away towards the bottom of the phone. Then, as indicated, pull the SIM card out.
To remove the SIM card, start by pressing the top of the card and push down and away towards the bottom of the phone. Then, as indicated, pull the SIM card out.
Step 7
- Begin to slowly lift the back casing of the phone. You should hear a snap when the casing is released.
- The power, volume, and camera buttons may fall out when separating the front and back casing.
Begin to slowly lift the back casing of the phone. You should hear a snap when the casing is released.
The power, volume, and camera buttons may fall out when separating the front and back casing.
Step 8
- Your casing should be separated and the three loose buttons put to the side.
- Be aware of the wiring on the top of the phone. Make sure not to pull it apart when separating the case.
Your casing should be separated and the three loose buttons put to the side.
Be aware of the wiring on the top of the phone. Make sure not to pull it apart when separating the case.
Step 9
- Slowly remove the back casing by gently pulling the ribbon connection.
Slowly remove the back casing by gently pulling the ribbon connection.
Step 10
- Gently pull on the wires to remove the front casing.
Gently pull on the wires to remove the front casing.
Step 11
- Your front casing and front speaker are now released.
Your front casing and front speaker are now released.
Step 12
Back Speakers
- Locate the back speaker.
Locate the back speaker.
Step 13
- Use the flat edge of the spudger to gently pry and remove the speaker.
Use the flat edge of the spudger to gently pry and remove the speaker.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Breanne
Member since: 04/12/2012
187 Reputation
5 Guides authored
Badges:
9
+6 more badges
Team
Cal Poly, Team 6-24, Amido Spring 2012
Member of Cal Poly, Team 6-24, Amido Spring 2012
CPSU-AMIDO-S12S6G24
3 Members
15 Guides authored
