Difficulty

Easy

Steps

7

Time Required

                          10 - 15 minutes

Sections

3

  • Backplate
  • 2 steps
  • Battery
  • 3 steps
  • Right Speaker
  • 2 steps

Flags

0

  • BackSamsung ATIV Smart PC 500T

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Backplate
  • Remove the stylus from the device.
  • Place the device screen-up on a hard surface, like a table.

Remove the stylus from the device.

Place the device screen-up on a hard surface, like a table.

1024

Step 2

  • Insert a plastic pry tool or opening pick between the glass and plastic case.
  • Work your way around the plastic edge, unclipping the backplate.
  • Once the clips are loosened, remove the backplate. Some force may be necessary.
  • Though you may need to use force, be careful of the pry tool slipping and hurting you!

Insert a plastic pry tool or opening pick between the glass and plastic case.

Work your way around the plastic edge, unclipping the backplate.

Once the clips are loosened, remove the backplate. Some force may be necessary.

Though you may need to use force, be careful of the pry tool slipping and hurting you!

Step 3

              Battery
  • Disconnect the three ribbon cables from the motherboard to free the battery.
  • Use your finger to lift the flap securing each ZIF connector.
  • Slide the ribbon cable out and towards you. Now it should be completely detached.
  • Repeat with the other two cables.

Disconnect the three ribbon cables from the motherboard to free the battery.

Use your finger to lift the flap securing each ZIF connector.

Slide the ribbon cable out and towards you. Now it should be completely detached.

Repeat with the other two cables.

Step 4

  • Get a firm hold of the power cable as close to the clip as you can.
  • Pull the power cable up and out of the clip.

Get a firm hold of the power cable as close to the clip as you can.

Pull the power cable up and out of the clip.

Step 5

  • Remove the six 3.5-mm screws using the Phillips #00 screwdriver.
  • Lift the battery out by hooking your finger under the tab on the top side of the battery and pulling it up and towards you. The battery should come out easily.

Remove the six 3.5-mm screws using the Phillips #00 screwdriver.

Lift the battery out by hooking your finger under the tab on the top side of the battery and pulling it up and towards you. The battery should come out easily.

Step 6

              Right Speaker
  • Locate the right speaker.
  • The right speaker is labeled with an “R.”
  • Locate the 3.5-mm screws and remove them with the Phillips #00 Screwdriver.

Locate the right speaker.

The right speaker is labeled with an “R.”

Locate the 3.5-mm screws and remove them with the Phillips #00 Screwdriver.

Step 7

  • Lift and remove the speaker from the device once the screws have been removed.

Lift and remove the speaker from the device once the screws have been removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Marissa Santana

Member since: 09/21/2015

267 Reputation

                                      1 Guide authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Baylor, Team 6-6, Williams Fall 2015                        

                                                  Member of Baylor, Team 6-6, Williams Fall 2015 



                    BU-WILLIAMS-F15S6G6                     


                                            3 Members                     


                                            10 Guides authored