Difficulty
Difficult
Steps
10
Time Required
30 minutes
Sections
2
- Power Cord
- 4 steps
- Disc Reader
- 6 steps
Flags
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Better Introduction
Improve this guide by completing or revising its introduction.
BackSamsung BD-F5700
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Power Cord
- Use Phillips 0 Screwdriver to remove two (2), 10 mm rear screws.
- Use the iFixit opening tool to help separate the top plastic casing from the bottom metal casing.
- When opening the device, be careful to not damage the ribbon cable circled in image 3.
Use Phillips 0 Screwdriver to remove two (2), 10 mm rear screws.
Use the iFixit opening tool to help separate the top plastic casing from the bottom metal casing.
When opening the device, be careful to not damage the ribbon cable circled in image 3.
1024
Step 2
- Use Phillips 0 screwdriver to remove two (2), 10 mm screws from the plastic cover.
- Remove plastic cover from board.
Use Phillips 0 screwdriver to remove two (2), 10 mm screws from the plastic cover.
Remove plastic cover from board.
Step 3
- Pull upward on back of the black and white wire to dislocate the black tab piece from device.
- To remove the cord from the device entirely, press on the white tab in the device and gently pull.
Pull upward on back of the black and white wire to dislocate the black tab piece from device.
To remove the cord from the device entirely, press on the white tab in the device and gently pull.
Step 4
- Insert the iFixit Opening tool into the black tab on the power cord, and use leverage to open the black tab.
- Pull the tab off the wire so that it can be placed on the replacement cord.
Insert the iFixit Opening tool into the black tab on the power cord, and use leverage to open the black tab.
Pull the tab off the wire so that it can be placed on the replacement cord.
Step 5
Disc Reader
- Firmly grip the hard plastic tab attached to the base and pull upwards.
- It is important to not tear the ribbon cables.
Firmly grip the hard plastic tab attached to the base and pull upwards.
It is important to not tear the ribbon cables.
Step 6
- Remove the two 7mm screws with a Phillips #1 screwdriver.
Remove the two 7mm screws with a Phillips #1 screwdriver.
Step 7
- Pinch both tabs on the side of the disc tray, push towards the front, and lift the disc tray out to remove.
Pinch both tabs on the side of the disc tray, push towards the front, and lift the disc tray out to remove.
Step 8
- Flip up the black locking tab on the ZIF connector.
Flip up the black locking tab on the ZIF connector.
Step 9
- Remove the 10 mm screw using a Phillips #1 screwdriver.
- Remove the small metal bar by pulling it outwards.
Remove the 10 mm screw using a Phillips #1 screwdriver.
Remove the small metal bar by pulling it outwards.
Step 10
- Flip the disc tray over so the laser points downward.
- Pull the disc reader out of the disc tray.
Flip the disc tray over so the laser points downward.
Pull the disc reader out of the disc tray.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 6 other contributors
Livan Perez
Member since: 02/15/2018
285 Reputation
2 Guides authored
Badges:
5
+2 more badges
Team
USF Tampa, Team S16-G4, Boczar Spring 2018
Member of USF Tampa, Team S16-G4, Boczar Spring 2018
USFT-BOCZAR-S18S16G4
4 Members
4 Guides authored
